Showing all 11 results
AXM-100 High Voltage Tach Adapter
$65.00Many older tachometers trigger off the negative terminal of the ignition coil. Often, these use a filtering circuit which will not trigger when given a 0 to 12 volt square wave signal, such as the tach output signal from an ECU or ignition box. If you h...
Add to cartUSB to Serial Adapter – Trouble Free!!
$28.99Important Note: The original USB2920 was discontinued by its manufacturer. We are now providing an updated part, but we are continuing using the same part number to make it easy for you to find. This FTDI chipset USB to Serial Adapter has been tested...
Add to cart4 Pin M8 Serial Cable
$31.50Replacement M8 to DB9 serial cable. This cable is used for certain plug and play applications where there wasn't room for a regular DB9 connector, including the following:MS3Pro PNP for '84-'87 Buick Regal 3.8 Turbo MSPNP Gen 2 for '86-'93 Ford M...
Add to cartElectronic Boost Control (EBC) Solenoid Kit
$58.00This electronic boost control solenoid can be used with the MS3-Pro/MSPNP as well as any DIY Style MegaSquirt EMS (with the appropriate mods), or with other electronic boost controllers to control boost by adjusting the pressure to a turbo wastegate. Th...
Add to cartDB15 Pigtail Harness
$21.00DB15 pigtail harness. Used for optional outputs on the expansion connector on V3.57 boards and for the V1.2 version of the MSPNP Gen 2 (the version with the red main board).
Add to cartDB26 Pigtail Harness
$21.00DB26 pigtail connector, as used with the latest MSPNP Gen 2 for its 26 pin expansion connector. Includes 6" pre crimped wires. Poke in the ones you need, leave out the ones you don't.
Add to cartMSPNP 12 Pin Center Connector
$18.4912 pin connector with pre-crimped 8" black wires. Included with MSPNP-MM9697 for extra inputs and outputs. Can also be used with DIYPNPN76-K, DIYBOB-N76K, or to repair factory wiring harnesses.
Add to cartMSPNP 16 Pin Center Connector
$19.9516 pin connector with pre-crimped 8" black wires. Included with MSPNP-MM9093 and MSPNP-MM9495 for extra inputs and outputs. Can also be used with DIYPNPN76-K, DIYBOB-N76K, or to repair a factory wiring harnesses.
Add to cartMSPNPPro-E36 20 Pin Options Connector
$27.0020 pin connector with pre-crimped 8" black wires. Used for options port on MSPNPPro-E369395. This is normally included with the MS3Pro PNP package; order this if you need a replacement.
Add to cartMSPNP and DIYPNP IAT Sensor Kit – Steel Bung
$34.00MegaSquirtPNP and DIYPNP IAT Sensor Kit - Steel BungThis is a simple kit to make it easier for you when removing your AFM/MAF when using a MegaSquirtPNP or DIYPNP. In many cases, the air temperature sensor is built into the MAF, so removing it will re...
Add to cartMSPNP and DIYPNP IAT Sensor Kit – Aluminum Bung
$33.50MegaSquirtPNP and DIYPNP IAT Sensor Kit - Aluminum BungThis is a simple kit to make it easier for you when removing your AFM/MAF when using a MegaSquirtPNP or DIYPNP. In many cases, the air temperature sensor is built into the MAF, so removing it will...
Add to cart