Quick Links

Ignition/Coil Connectors

EPA, CARB & Emissions Disclaimer- All ECU's are for race purposes only. It's your responsibility to remain in compliance with all federal, state, provincial, or other laws that apply to you.

Showing all 11 results

  • Pigtail Connector for IGN1A and GM MAF Sensors


    4' Flying lead smart coil pigtail for IGN-1A coils.  The extra length makes these easy to bundle up into a single ignition control harness without needing splices near the coil. Power and primary ground wires are 18 gauge to better handle these coils' p...

    Add to cart
  • Crimp Connector for IGN-1A

    5 out of 5

    Connector for IGN-1A coils, includes crimp on terminals/pins. Like all of our 'ready to crimp' connectors- we include an extra terminal/pin, just in case.  Click here to see other ignition system components for your project!  

    Add to cart
  • Wire – Single Core Shielded Ignition Signal Wire 20 Gauge – 10′


    Wire - Single Core Shielded Ignition Wire 20 Gauge - Length = 10' Shielded single core 20 gauge wire helps cut out interference -- Perfect for Tach/Ignition Signal! This temperature resistant wire has one 20 gauge wires in the shield. Has many other us...

    Add to cart
  • Crimp Connector for IGN-1 or IGN-1CD


    Metri-Pack crimp connector for wiring up IGN-1 or IGN-1CD coils. Like all of our 'ready to crimp' connectors- we include an extra terminal/pin, just in case you goof one up.

    Add to cart
  • Crimp Connector for IGN-4


    Crimp connector and pins for IGN-4 coil. This is a standard "junior timer" sort of connector that has other uses such as Bosch crankshaft position sensors and throttle position sensors. Like all of our 'ready to crimp' connectors, we include an extra t...

    Add to cart
  • Crimp Connector for IGN-6


    Included is a Weather Pack type connector for IGN-6 coils. The pins and seals are sized for 14 to 16 gauge wire. Like our other DIYAutoTune Weather Packs, we include an extra pin, just in case.

    Add to cart
  • 2 Wire VSS/Ignition Connector


    This 2 wire pigtail connector replaces GM part number 12101855. Used on a variety of applications, including some distribtutorless ignitions, vehicle speed sensors, and many chassis wiring locations. Please check mating connectors before ordering.

    Add to cart
  • 5 Wire Pigtail for GM DIS Modules


    This pigtail connector fits some GM OBD-I external DIS modules, including most 1995 and earlier Saturns. Check your module for the "missing pin" position to make sure this is the right one for your module. Replaces GM part number 12101880

    Add to cart
  • Black Pigtail for Ford TFI Ignitions


    Black Ford TFI module connector. Note that this is not keyed the same way as the gray connector; the notch on the right side of this connector in the photo is on the left side of the gray connector. Check your module before ordering.

    Add to cart
  • Gray Pigtail for Ford TFI Ignitions


    Gray connector fits certain Ford TFI systems. We've confirmed this was used on certain 5.0 Mustangs among other applications. It also appears to fit some neutral safety switches and distributorless ignitions. Note that the gray color is not purely a cosme...

    Add to cart
  • Ignition Coil Pigtail for Ford TFI


    This pigtail has 10" leads and fits Ford TFI ignition coils. Used on 5.0 Mustangs, injected 351 Windsor motors, the 2.3 Turbo, various incarnations of the 3.8 V6, and many others. Just the thing if you're making a new wiring harness for your 5.0 or other ...

    Add to cart