Showing 1–16 of 20 results
8′ MegaSquirt Wiring Harness (MS1/MS2/MS3 Ready)
$83.00MegaSquirt Wiring Harness - 8 Feet LongWe've completely redesigned our wire harness to help you get your fuel injection installation right the first time with several new features to help make your installation as easy and reliable as possible:...
Add to cartUSB to Serial Adapter – Trouble Free!!
$28.99Important Note: The original USB2920 was discontinued by its manufacturer. We are now providing an updated part, but we are continuing using the same part number to make it easy for you to find. This FTDI chipset USB to Serial Adapter has been tested...
Add to cartMS230-K Kit with MapDaddy4 Upgrade
$388.00Important Note: Due to supply chain challenges and the lack of ability to have parts anodized at this time, we are transitioning the enclosure used with our MS2 ECUs. Your MS2 will now include a brushed silver finish MS3 enclosure, which will help ...
Add to cartMegaSquirt-II Programmable EFI System PCB3.0 – Kit
$324.00Important Note: Due to supply chain challenges and the lack of ability to have parts anodized at this time, we are transitioning the enclosure used with our MS2 ECUs. Your MS2 will now include a brushed silver finish MS3 enclosure, which will help ...
Add to cartMegaSquirt Tuning Cable (DB9 Straight Thru)
$5.50DB9 6' Male/Female Straight thru cable for tuning and testing your MegaSquirt ECU.
Add to cartMegaSquirt Relay Board – Assembled Unit
$130.00MegaSquirt Relay Board - Assembled Unit - Part# MSRelay-CThough the Relay/Power Board is not required, it is a convenience and can reduce the chance of miswiring during the installation. The relay board provides a central place for all of the required...
Add to cartMegaSquirt Relay Cable
$89.00High Quality 4' Relay Board cable for connecting your MegaSquirt ECU to your Relay Board.Works with MS1, MS2, or MS3, all standard main boards (includes not just the IAC and ignition pins - it also has the spare pins on 3 through 6). It has a shielded...
Add to cartMegaSquirt Wiring Bundle – Long
$48.00MegaSquirt Wiring Bundle8' TXL wire, color coded with labeling printed on the wire every 3 inches -- no paper tags here! IAC and Ignition wires are included for MS-I / MS-2 use (or MS-3 Primary Harness use) Shielded Ignition input wireGrea...
Add to cartJimStim v1.5 MegaSquirt Stimulator with Wheel Simulator – Unassembled
$80.00Use this board to test the MegaSquirt's inputs and outputs on the bench, before you install it on a car!The JimStim features a microcontroller which allows the simulation of up to 30 different toothed wheels, in addition to the standard distributor s...
Add to cartJimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled
$120.00DIYAutoTune Part# JimStim-CJimStim is essentially an engine simulator, a microcontroller which allows the generates up to 30 different toothed wheel signals, in addition to the standard distributor signal. Test your RPM input on the Stim, or tell the ...
Add to cartJimStimX MS3X Stimulator Expansion Board – Unassembled
$52.00The regular JimStim can test the main board on your MS3. But what if you'd like to see the inputs and outputs on the MS3X expansion card in action, too? Now it's easy - just add a JimStimX! Use the three pull-off jumpers on the JimStim to connect the 5 vo...
Add to cartDB15 Pigtail Harness
$21.00DB15 pigtail harness. Used for optional outputs on the expansion connector on V3.57 boards and for the V1.2 version of the MSPNP Gen 2 (the version with the red main board).
Add to cartDIYPNP Upgrade: Sequential Injection Kit
$44.00Add two extra injector drivers to your DIYPNP with this new module and the latest MS2/Extra code! We've partnered with JBPerf to develop this tiny module with two extra injector drivers. Allows for fully sequential injection on a 4 cylinder engine, semi-s...
Add to cartCPU – MegaSquirt-II Daughterboard
$136.00MegaSquirt-II DaughterboardFor upgrading your Megasquirt-I ECU, or replacement of your damaged MegaSquirt-II daughterboard. MS2 daughter cards are for use only with genuine Bowling & Grippo MegaSquirt mainboard PCBs. This is the latest version o...
Add to cartJumper 10-Pack
$7.4910-pack of wire jumpers in 5 colors. These fit 0.1" headers and are used on the JimStim to make connections for testing additional circuitry. There are several other uses for them too.
Add to cartDB15 Metalized Plastic Backshell
$2.50Metalized plastic backshell for the DB15 spare I/O connector, as used on our DIYPNP, VVTuner, and V3.57 boards.
Add to cart