Cart

Quick Links

MS3Pro PNP Accessories

With the MS3Pro PNP EMS, we’ve simply taken all of the wiring homework and labor out of the project for you, and given you a solid base map to tune from to make your installation and tuning process go incredibly smoothly whether you’re a super technical computer-geek, or maybe not as interested in all the technical side of things and just ready to get tuning. These accessories make installation a snap!

 

EPA, CARB & Emissions Disclaimer- ECU's are for race purposes only.

Showing all 11 results

  • AXM-120 VR conditioner

    $70.00

    Use this module to convert the sine wave signal from a VR (variable reluctor) signal into an easy to handle square wave.  The AXM-120 VR conditioner works with camshaft position, crankshaft position, vehicle speed, or similar sensors. Common uses for thi...

    Add to cart
  • AXM-110 High Voltage Isolator

    $68.99

    This module protects your engine or transmission controller from high voltage spikes being fed in through digital inputs. The AXM-110 module can take 1,500 volts peak and 33.5 volts continuous. Common uses for the AXM-110 high voltage isolator include: ...

    Add to cart
  • AXM-100 High Voltage Tach Adapter

    $65.00

    Many older tachometers trigger off the negative terminal of the ignition coil.  Often, these use a filtering circuit which will not trigger when given a 0 to 12 volt square wave signal, such as the tach output signal from an ECU or ignition box. If you h...

    Add to cart
  • USB to Serial Adapter – Trouble Free!!

    4.7916666666667 out of 5
    $28.99

    This FTDI chipset USB to Serial Adapter has been tested and works properly with all of our ECU products and all versions of TunerStudio on a wide range of operating systems.  This is probably the most common item we see people come back for after a purch...

    Add to cart
  • 4 Pin M8 Serial Cable

    $31.50

    Replacement M8 to DB9 serial cable. This cable is used for certain plug and play applications where there wasn't room for a regular DB9 connector, including the following: MS3Pro PNP for '84-'87 Buick Regal 3.8 Turbo MSPNP Gen 2 for '86-'93 Ford M...

    Add to cart
  • Electronic Boost Control (EBC) Solenoid Kit

    5 out of 5
    $62.99

    This electronic boost control solenoid can be used with the MS3-Pro/MSPNP as well as any DIY Style MegaSquirt EMS (with the appropriate mods), or with other electronic boost controllers to control boost by adjusting the pressure to a turbo wastegate. Th...

    Add to cart
  • MS3Pro Plug & Play 26 Pin Options Port Connector Package

    $29.99

    Includes connector shell, pins & wiring for your specific feature outputs.  Only pin the options you will be using. Compatible with MS3Pro Plug & Play 26 pin options port.

    Add to cart
  • MSPNPPro-E36 20 Pin Options Connector

    $27.00

    20 pin connector with pre-crimped 8" black wires. Used for options port on MSPNPPro-E369395. This is normally included with the MS3Pro PNP package; order this if you need a replacement.

    Add to cart
  • MSPNP and DIYPNP IAT Sensor Kit – Steel Bung

    5 out of 5
    $39.99

    MegaSquirtPNP and DIYPNP IAT Temperature Sensor Kit - Steel Bung This is a simple kit to make it easier for you when removing your AFM/MAF when using a MegaSquirtPNP or DIYPNP. In many cases, the air temperature sensor is built into the MAF, so removin...

    Add to cart
  • MSPNP and DIYPNP IAT Temperature Sensor Kit – Aluminum Bung

    4.5 out of 5
    $39.99

    MegaSquirtPNP and DIYPNP IAT Sensor Kit - Aluminum Bung This is a simple kit to make it easier for you when removing your AFM/MAF when using a MegaSquirtPNP or DIYPNP. In many cases, the air temperature sensor is built into the MAF, so removing it will...

    Add to cart