Showing all 16 results
AXM-100 High Voltage Tach Adapter
$65.00Many older tachometers trigger off the negative terminal of the ignition coil. Often, these use a filtering circuit which will not trigger when given a 0 to 12 volt square wave signal, such as the tach output signal from an ECU or ignition box. If you h...
Add to cartMS3Pro Module F1/F2 Replacement Fuse
$3.00The MS3Pro ECU’s feature user-replaceable fuses that protect against voltage spikes and other abuse. To replace these fuses, use a needle nose pliers to pull the fuse out of its holder, and then push in the replacement fuse by hand.This is the 100...
Add to cartMS3Pro Ultimate F4/F6 Replacement Fuse
$2.00The MS3Pro ECU’s feature user-replaceable fuses that protect against voltage spikes and other abuse. To replace these fuses, use a needle nose pliers to pull the fuse out of its holder, and then push in the replacement fuse by hand.This is the 375...
Add to cartGen 1 MS3Pro F1/F2 + EVO F4 Replacement Fuse
$2.25The MS3Pro ECU’s feature user-replaceable fuses that protect against voltage spikes and other abuse. To replace these fuses, use a needle nose pliers to pull the fuse out of its holder, and then push in the replacement fuse by hand.These 500mA fus...
Add to cartMS3Pro Ultimate + EVO F5 Replacement Fuse
$3.00The MS3Pro ECU’s feature user-replaceable fuses that protect against voltage spikes and other abuse. To replace these fuses, use a needle nose pliers to pull the fuse out of its holder, and then push in the replacement fuse by hand.This is the 6000m...
Add to cartMS3Pro EVO Uncrimped AMPSEAL Connectors
$60.00Making your own harness? This plug and pin kit features the MS3Pro AMPSEAL white & gray connectors plus 75 pins- more than enough for making your own MS3Pro EVO or 1st Gen harness.MS3Pro ULTIMATE 3-connector AMPSEAL Kit available here
Add to cartMS3Pro ULTIMATE Uncrimped AMPSEAL Connectors
$82.00Planning to make your own ULTIMATE harness? This plug and pin kit features the MS3Pro ULTIMATE AMPSEAL white, black & gray connectors, plus 100 pins- more than enough for making your own!(EVO/ 1st Gen 2-connector AMPSEAL Kit sold separately)
Add to cartMS3Pro 1st Gen Wiring Harness Upgrade (for ULTIMATE and EVO)
$22.00If you have a previously installed MS3Pro harness (1st Gen flying lead or LS Drop On Harness) and want to upgrade to MS3Pro EVO or ULTIMATE ECU, the upgrade path is simple. However, complete functionality will require a few basic changes to your 1st Ge...
Add to cartUSB to Serial Adapter – Trouble Free!!
$28.99Important Note: The original USB2920 was discontinued by its manufacturer. We are now providing an updated part, but we are continuing using the same part number to make it easy for you to find. This FTDI chipset USB to Serial Adapter has been tested...
Add to cartTuning Cable – MS3Pro EVO & ULTIMATE ECU’s
$31.50Connect MS3Pro ULTIMATE or EVO directly to your laptop with this 4 pin M12 serial cable.
Add to cartSealed resistor – 10K
$4.50We've wrapped a 10K, 1/4 watt resistor in a sealed and strain-relieved package for underhood use. Red heat shrink tubing with yellow leads. Typically used as a shunt resistor with VR sensors.
Add to cartSealed resistor – 1K
$4.50We've wrapped a 1K, 1/4 watt resistor in a sealed and strain-relieved package for underhood use. Blue heat shrink tubing with blue leads. Suggested uses include a pull-up resistor for Hall effect and optical sensors, and for spark outputs C and D on a Mic...
Add to cartElectronic Boost Control (EBC) Solenoid Kit
$58.00This electronic boost control solenoid can be used with the MS3-Pro/MSPNP as well as any DIY Style MegaSquirt EMS (with the appropriate mods), or with other electronic boost controllers to control boost by adjusting the pressure to a turbo wastegate. Th...
Add to cart