Search Results for: crank sensor
Ignition Control – DIYPNP v1.5
Ignition control is one of the more involved parts of the DIYPNP installation to set up, and may take a bit of trial and error if you do not have an application guide to cover what mods you need. This page will explain the ignition control, both the inputs and the outputs. We’ve made the…
Read MoreDIYPNP V1.5
The DIYPNP board lets you build your own plug and play engine management systems. The core of the DIYPNP kit is a MicroSquirt module that plugs into an expansion ‘mainboard’ with on board circuits for many features, including direct coil control, boost control, knock control, and several general purpose inputs and outputs. You assemble this…
Read MoreMegaSquirt Carb to EFI Conversion – Part 2: Ignition Control
From Carb to EFI, with Ignition Control, on just a fistful of dollars… Objective of this Article This article will walk you through the process of installing a MegaSquirt EFI system on a classic carb’d vehicle attempting to go the least expensive route possible using junkyard parts and DIY ingenuity. We’ll be using an MegaSquirt-II…
Read MoreDIYPNP FAQ
UPDATE: Unfortunately, the DIYPNP product line has reached it’s end of life. This F.A.Q. page will remain available for archive purposes. Is a DIYPNP fully assembled? Do I just plug it in when it arrives? The DIYPNP ships in kit form and allows you to build a Plug-N-Play EMS for an incredible number of vehicles…
Read MoreThere are several ‘optional’ or ‘choice required’ steps during assembly of the PCBv3 MegaSquirt units, how are the DIYAutoTune ECU’s configured?
MegaSquirt-I EMS’s are setup by default as a fuel only EFI controller running though they are running the current stable release of the MS1/Extra firmware. These are configured to be triggered from the (-) negative terminal of the coil by default. It is fairly easy to convert them to be triggered from a Hall/Optical/Points trigger…
Read MoreWhere do I start?
Read. Then read some more. If you skip this step you will be asking questions later that you could already know the answers to. We’re always glad to help though as this is a DIY based system some of the burden does fall on the user to do their homework, the big dogs charge an extra…
Read MoreAdjusting the MegaSquirt V3.0/V3.57 VR Conditioner
The MegaSquirt V3.0 and later is designed to be able to read a wide variety of variable reluctor crankshaft position sensors. This is no easy task to get one circuit to handle a wide spectrum of sensors, and so there is a fair amount of adjustability built into the MegaSquirt. Customers asked for a simpler…
Read MoreHow to use an EEC-IV Adapter Board to MegaSquirt your Ford
If you haven’t already, please read the ‘disclaimer’ at the top of the parent page here. Note – this adapter has been discontinued. This article is for legacy support. What does this board do? The EEC-IV adapter board kit allows you to install MegaSquirt into virtually any Ford vehicle that uses an EEC-IV computer, without…
Read MoreHow to MegaSquirt Your Nissan 240SX
How to MegaSquirt your Nissan 240SX Updated 4/10/2019 – notes on ECCS relay with MSPNP added Using the stock ignition module with MegaSquirt Application(s): 1989-1998 Nissan 240SX with KA24E or KA24DE Other vehicles with KA series engines, such as Nissan pickup trucks, are similar. This also works for distributor equipped versions of the SR20DE and…
Read More
Jet Boat Journey: Harnessing the Power of MicroSquirt EFI
In this exclusive interview with DIYAutoTune.com, Nicholas Bolton takes us on a thrilling journey into the world of jet boats. Discover how he harnesses the power of Microsquirt EFI to revolutionize his boat’s performance on the water. From engine configurations to race endeavors, Nicholas shares his insights and experiences, showcasing the immense potential of electronic fuel injection in the marine realm.
Read More