Showing 113–128 of 129 results
-
MegaSquirt PWM IAC Valve Control (TIP120) ‘Mod-Kit’
$9.99These are the parts needed for the 'TIP120 PWM idle valve' mod. If you are installing all optional components on the v3 heat sink (leaving no extra space for this transistor there) then you can drill a hole in your case and use it as your heat sink or a...
Add to cart -
MegaSquirt Pull-up Resistors Mod Kit
$3.99Six 1k 1/4w resistors, and four 470ohm 1/4w resistors. Perfect for use as 'pullup resistors' for your MS ECU modding needs. These can be used for several of the mods described in some of our car-specific install articles listed on the site. NOTE: Th...
Add to cart -
MegaSquirt Relay Control Mod Kit (VTEC, TVIS, Fans)
$9.99Modkit used to build a relay control circuit, suitable for switching a relay on/off and controlling fans, VVT, VTEC, TVIS, anything a relay can control. Usable on the PCBv3.0, v3.57 or PCBv2.2 ECUs Information and an example of how to implement this...
Add to cart -
MegaSquirt Ford Bias Resistors Mod Kit
$3.99This is a simple two-part kit with two 1/4w 27kohm metal film resistors to replace R4 and R7 in any MegaSquirt PCB2.2 or PCB3.0 ECU. This will allow for use of the stock Ford temperature sensors without recalibrating the MegaSquirt for the Ford sensors. N...
Add to cart -
IAT Sensor Kit – Steel Bung
$34.99Streamline your AFM/MAF removal process with our kit designed for AMP|EFI ECUs. When removing the air flow meter, you'll often need to relocate the air temperature sensor, as many MAF units have it built in. This kit provides everything you need to instal...
Add to cart -
IAT Temperature Sensor Kit – Aluminum Bung
$34.99Simplify your AFM/MAF removal process with our comprehensive kit designed for use with AMP|EFI ECUs. When removing the air flow meter, you’ll often need to relocate the air temperature sensor, as many MAF units have this sensor built in. Our kit provide...
Add to cart -
DIYPNP Upgrade: Ignition Module and Heat Sink Kit
$12.00High current ignition driver kit with heatsink designed for the DIYPNP ECU. It includes the OnSemi EcoSPARK IGBT. This is the same high current ignition driver as used in many of our current ECU products as well as the QuadSpark ignition module, after...
Add to cart -
DIYPNP Upgrade: BIP373 Ignition Module and Heat Sink Kit
$12.00Add a BIP373 Ignition Module with Heat Sink to your DIYPNP EMS to directly fire coils that do not have their own internal ignitor. This will allow you to convert vehicles that came with a single coil ignition system and distributor over to modern day ...
Read more -
Ford 60 Pin EEC4 EECIV PCM Connector
$26.00With the Ford EEC-IV (aka EEC4) 60 Pin PCM Connector, you can build professional adapter harnesses connecting the engine management system of your choice to a wide variety of Ford cars. This one fits cars with a Ford EEC-IV 60 pin ECU. See the DIYBOB main...
Read more -
MegaSquirt PCB3.0 Heatsink Only
$10.00This is a precision-machined aluminum heatsink designed specifically for the MegaSquirt PCB Version 3.0 main board. Built from 1/8" aluminum, it provides efficient cooling for power-handling components such as the voltage regulator and ignition drivers, e...
Add to cart -
IAC Valve Pigtail (6″)
$8.49IAC Pigtail (6") for Jeep Stepper Motor Idle Air Controllers This is the wiring pigtail to compliment DarkStar's IAC Valve body complete with detailed assembly instructions (it's super easy- basically just plug them in) so that you can color code the w...
Add to cart -
GM CLT Sensor Connector with Uncrimped Terminals
$4.99GM CLT Sensor Connector Only (Uncrimped) Complete with the connector, two pins, plus an extra pin (just in case) total of 3 Pins provided
Add to cart -
TPS Connector (GM 3 Pin Style)
$6.49TPS-3 Connector (Uncrimped) GM Style 3-pin TPS Connector complete with: the 3-pin connector three pins plus an extra fourth pin (just in case)
Add to cart -
TPS Pigtail (GM 3 Pin Style)
$8.00GM Style 3-pin TPS Pigtail used in many GM applications, as well as others.... 6" Pigtail, pre-crimped, ready for your harness.
Add to cart -
DIYAutoTune 14″ White Cut Vinyl Decal / Sticker
$3.00These are high quality WHITE cut out vinyl decals- DIYAutoTune Logo Size is 14" long by 1.5" high.
Add to cart -
DIYAutoTune.com 6″ Decal / Sticker
$0.50These are high quality vinyl decals. Clear background with white text that will look great on tinted windows. The adhesive is on the back so they adhere to the outside of the vehicle and the vinyl and printing is made to handle the environment pretty well...
Add to cart
