Showing 209–224 of 229 results
-
LM2937ET-5.0-ND 5 Volt Regulator
$3.99BA05CC0T 5 volt regulator, used as a higher capacity replacement for LM2937ET-5.0-ND. U5 in both the V2.2 and V3.0 kits.
Add to cart -
MC34072APG Op Amp – V3.0 U7
$3.108 pin op amp - U7 from the V3.0 kit. We are now using the MC34072APG instead of the LM2904.
Add to cart -
Chip Component Pack – Optoisolator, FET Driver, and RS232
$9.00Service replacement component pack. Includes: 160-1300-5-ND optoisolator IXDI404PI-ND MOSFET driver 497-2055-5-ND RS232 chip 40 pin socket.
Add to cart -
Transistor Replacement 5 – Pack PN2222AD26ZCT-ND
$3.105 pack of PN2222AD26ZCT-ND NPN transistors. Replacement for V2.2 Q3, Q5, Q9-Q11
Add to cart -
IRFIZ34G-ND FETs 2 Pack (V2.2 Q2 and Q7, V3.0 Q1 and Q5)
$3.99Set of 2 IRFIZ34G-ND FET transistors. Q1 and Q5 in the V3.0 kits. Q2 and Q7 in the V2.2 kits.
Add to cart -
3″ Trigger Wheel Spacer
$8.003" diameter, 1/4" thick spacer for our trigger wheels. Has a 1/2" center wheel and notches for locating bolts.
Add to cart -
2″ Trigger Wheel Spacer
$6.002" diameter, 1/4" thick spacer for our trigger wheels. Has a 1/2" center wheel and notches for locating bolts.
Add to cart -
MSPNP and DIYPNP IAT Sensor Kit – Steel Bung
$39.99MegaSquirtPNP and DIYPNP IAT Sensor Kit - Steel Bung This is a simple kit to make it easier for you when removing your AFM/MAF when using a MegaSquirtPNP or DIYPNP. In many cases, the air temperature sensor is built into the MAF, so removing it will re...
Add to cart -
MSPNP and DIYPNP IAT Sensor Kit – Aluminum Bung
$39.99MegaSquirtPNP and DIYPNP IAT Sensor Kit - Aluminum Bung This is a simple kit to make it easier for you when removing your AFM/MAF when using a MegaSquirtPNP or DIYPNP. In many cases, the air temperature sensor is built into the MAF, so removing it will...
Add to cart -
DIYPNP Upgrade: BIP373 Ignition Module and Heat Sink Kit
$12.00Add a BIP373 Ignition Module with Heat Sink to your DIYPNP EMS to directly fire coils that do not have their own internal ignitor. This will allow you to convert vehicles that came with a single coil ignition system and distributor over to modern day ...
Read more -
DIYPNP Upgrade: Ignition Module and Heat Sink Kit
$12.00High current ignition driver kit with heatsink designed for the DIYPNP ECU. It includes the OnSemi EcoSPARK IGBT. This is the same high current ignition driver as used in many of our current ECU products as well as the QuadSpark ignition module, after...
Add to cart -
Ford 60 Pin PCM Connector
$26.00With the Ford 60 Pin PCM Connector, you can build professional adapter harnesses connecting the engine management system of your choice to a wide variety of Ford cars. This one fits cars with a Ford EEC-IV 60 pin ECU. See the DIYBOB main page for an appl...
Add to cart -
MegaSquirt PCB3.0 – Heat Sink Only
$10.00Heat Sink Machined for MegaSquirt PCB version 3.0 Part# MSx30-HS
Add to cart -
IAC Valve Pigtail (6″)
$8.49IAC Pigtail (6") for Jeep Stepper Motor Idle Air Controllers This is the wiring pigtail to compliment DarkStar's IAC Valve body complete with detailed assembly instructions (it's super easy- basically just plug them in) so that you can color code the w...
Add to cart -
IAC Valve Connector with Crimp Terminals
$6.99IAC Valve Connector (Uncrimped) Complete with the connector, four pins, plus an extra pin (just in case)
Add to cart -
TPS Connector (GM 3 Pin Style)
$6.49TPS-3 Connector (Uncrimped) GM Style 3-pin TPS Connector complete with: the 3-pin connector three pins plus an extra fourth pin (just in case)
Add to cart