Search Results for: JimStim
JimStim v1.5 MegaSquirt Stimulator with Wheel Simulator – Unassembled
SKU: jimstim-k
$80.99
Use this board to test the MegaSquirt’s inputs and outputs on the bench, before you install it on a car! The JimStim features a microcontroller which allows the simulation of up to 30 different toothed wheels, in addition to the standard distributor signal of the standard stimulator. Instead of having the Megasquirt set to “Stim for…
View Details-
Add to cart
JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled
SKU: jimstim-c
$119.99
DIYAutoTune Part# JimStim-C JimStim is essentially an engine simulator, a microcontroller which allows the generates up to 30 different toothed wheel signals, in addition to the standard distributor signal. Test your RPM input on the Stim, or tell the JimStim to provide a signal like the one from a Neon, Miata, Subaru, most Fords, and…
View Details-
Add to cart
JimStim CPU
SKU: JimStim-CPU
$12.99
Included is the JimStim CPU. A microcontroller loaded with the latest code, currently V2.0.4.
View Details-
Add to cart
MegaSquirt JimStim Stimulator Power Supply
SKU: StimPower
$17.50
12v DC Power Supply Plugs directly into your MegaSquirt JimStim Stimulator! Power supply supports 120 to 240 volt AC power.
View Details-
Add to cart
JimStimX Kit – MS3X Stimulator Expansion Board – Unassembled
SKU: JimStimX-K
$51.99
The regular JimStim can test the main board on your MS3. But what if you’d like to see the inputs and outputs on the MS3X expansion card in action, too? Now it’s easy – just add a JimStimX! Use the three pull-off jumpers on the JimStim to connect the 5 volt power, ground, and cam…
View Details-
Add to cart
Jumper 10-Pack
SKU: jumper.1
$7.49
10-pack of wire jumpers in 5 colors. These fit 0.1″ headers and are used on the JimStim to make connections for testing additional circuitry. There are several other uses for them too.
View Details-
Add to cart
Variable Resistor P3C3103-ND – Stim Pot
SKU: P3C3103-ND
$3.00
Variable resistor P3C3103-ND, 10K This is the potentiometer (pot) used in the MSStim22 and JimStim kits, as well as the TransStim P1 and P2. If you need to replace a worn out one, get a new one here. Sold individually.
View Details-
Add to cart
CP-102A-ND Power Jack Connector
SKU: CP-102A-ND
$3.00
Replacement CP-102A-ND power jack connector. 5.5 mm OD, 2.1 mm ID. Used on the Stimulator, JimStim, and DIYPNP to connect to a power supply.
View Details-
Add to cart
MegaSquirt-3 with PCB V3.0 Kit
SKU: MS330-K
$449.99
Included is a MegaSquirt-III Engine Management System w/PCB3.0 – Unassembled Kit Part # MS330-K This MS330-K kit includes everything you will need to build your MegaSquirt-3. The genuine B&G partial kit with V3.0 PCB, everything in the standard Bill Of Materials, the MS3 daughter board kit, the case, pre-machined endplates and heatsink bar, even the…
View Details-
Add to cart
MegaSquirt-II Programmable EFI System PCB3.0 – Kit
SKU: MS230-K
$324.99
Note: Now using a brushed silver finish MS3 enclosure, which will help facilitate potential future upgrades from MS2 to MS3 without extra cost! MegaSquirt-II Engine Management System with 3.0 main board – Unassembled Kit; Part # MS230-K The MS230-K kit includes everything you will need to build your MegaSquirt-2. The genuine B&G partial kit with…
View Details-
Add to cart