Search Results for: MSPNP Miata
MegaSquirt MS3X Wiring Bundle – 23″
SKU: MS3X-SM_Bund
$29.99
MegaSquirt MS3X Wiring Bundle – Length = 23″ ~23″ of TXL High temp automotive grade wire. Color coded wiring with labeling printed on the wire every 6 inches — no paper tags here! Use with MS3X Expansion board or other sequential device Just like a short run of the MS3X harness, but with no DB37 connector. We…
View Details-
Add to cart
MegaSquirt-3 with PCB V3.0 Kit
SKU: MS330-K
$449.99
Included is a MegaSquirt-III Engine Management System w/PCB3.0 – Unassembled Kit Part # MS330-K This MS330-K kit includes everything you will need to build your MegaSquirt-3. The genuine B&G partial kit with V3.0 PCB, everything in the standard Bill Of Materials, the MS3 daughter board kit, the case, pre-machined endplates and heatsink bar, even the…
View Details-
Add to cart
MegaSquirt-III MS3X Expansion Card & Connector Kit
SKU: MS3Xpander
$110.49
Put this small circuit board in your MegaSquirt-III to unlock its full potential! This board installs in the MS3 case with no soldering; just connect it with the included ribbon cables. Install the MS3X board to add this whole list of inputs and outputs to the MS3 ECU: 8 Sequential fuel injection outputs. Each can…
View Details-
Add to cart
755 Piece Weather Pack Kit
SKU: WPL_755-K
$145.00
Our Weather Pack kits contains everything you need to get your project done right! We’ve used other connector kits available on the market in projects around the shop and they never quite met our expectations. So in typical DIYAutoTune style, we stepped it up and made them better! We’ve included more than enough crimp terminals…
View Details-
Add to cart
Weather Pack Bulkhead Connector Kit
SKU: WP22M-K
$32.00
Use this giant 22 Position Weather Pack connector to run wires through a firewall or as a quick disconnect for your engine harness, or other components that need a lot of wires. Includes: (1) 22 position male and female connector (13) 20-18 gauge male and female pins (13) 16-14 gauge male and female pins (4)…
View Details-
Add to cart
3/8″ NPT Stainless Steel Weld-On Bung for IAT or CLT Sensor
SKU: 38NPT-BungSS
$12.99
3/8″ NPT Stainless Steel Weld-On Bung for IAT or CLT Sensor Our 3/8″ pipe fitting for temperature sensors is now available in stainless steel. This one can be welded to either stainless or mild steel. Comes with galvanized steel plug as well.
View Details-
Add to cart
JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled
SKU: jimstim-c
$119.99
DIYAutoTune Part# JimStim-C JimStim is essentially an engine simulator, a microcontroller which allows the generates up to 30 different toothed wheel signals, in addition to the standard distributor signal. Test your RPM input on the Stim, or tell the JimStim to provide a signal like the one from a Neon, Miata, Subaru, most Fords, and…
View Details-
Add to cart
Innovate LC-2 Digital Wideband Controller with Sensor – 38770
SKU: INNVT-3877
$169.99
The evolution of the world’s most popular stand alone digital wideband O² sensor controller, the Innovate Motorsports LC-2 builds upon the legacy of the LC-1 by adding simplicity and leading edge technology. The LC-2’s circuitry is self-calibrating, so it compensates automatically for changes in temperature, altitude, and sensor condition. This Innovate LC-2 wideband system is…
View Details-
Add to cart
Fuel Injector Pigtails – Bosch EV1
SKU: InjPiggy-EV1-1
$8.00
Bosch Style Fuel Injector Plug with 6″ Wire Pigtail Fits a wide variety of cars that use Bosch injectors. This connector incorporates seals on the pins for maximum corrosion resistance and the spring wire has a quick release ability – just squeeze it at the top and it releases its grip on the injector. The…
View Details-
Add to cart
AMP’d MicroSquirt without harness
SKU: MicroSqrtAMPd
$339.99
This is the latest version of the MicroSquirt, only from AMP EFI and our dealers! The AMP’d MicroSquirt adds higher current capacity injector drivers, higher current capacity on its optioisolated input, and 4 user configurable option switches that activate on-board pullup resistors for applications that use hall or optical style crank and cam sensors.…
View Details-
Add to cart