Cart

Quick Links

755 Piece Weather Pack Kit

5 out of 5 based on 2 customer ratings
(2 customer reviews )

$145.00

In stock

Description

Our Weather Pack kits contains everything you need to get your project done right!  We’ve used other connector kits available on the market in projects around the shop and they never quite met our expectations.  So in typical DIYAutoTune style, we stepped it up and made them better!  We’ve included more than enough crimp terminals to get the job done right, and in several different sizes to ensure the connection is as secure as possible, even when you’re using lots of different wiring sizes in your harness. This kit picks up where our 460 piece kit leaves off, adding not only the 6 pin connectors, but also the seldom seen 5 pin connectors, and of course plenty of extra pins in case any crimps don’t turn out quite right.

755 Piece Weatherpack Kit Includes:

(4) 6 position male and female connectors
(3) 5 position male and female connectors
(6) 4 position male and female square connectors
(5) 4 position male and female flat connectors
(6) 3 position male and female connectors
(6) 2 position male and female connectors
(6) 1 position male and female connectors
(70) 20-18 gauge female pins
(70) 20-18 gauge male pins
(70) 16-14 gauge female pins
(70) 16-14 gauge male pins
(23) 12 gauge female pins
(23) 12 gauge male pins
(140) Green 20-18 gauge seals
(140) Gray 16-14 gauge seals
(46) Blue 12 gauge seals
(30) Plugs
(1) Terminal removal tool

weatherpack 755

Customer reviews

Rated 5 out of 5 stars
2 reviews
4 stars 0 0 %
3 stars 0 0 %
2 stars 0 0 %
1 star 0 0 %

2 reviews for 755 Piece Weather Pack Kit

  1. 5 out of 5

    Hall Effect Crankshaft Position SensorI bought this item, it's not dirt cheap to me. But, I purchased it. Using it with ms2 extra. Had to do few steps, solder few wires to make it work. Instructions online available step by step. It was easy enough and the felling was rewarding that I did it. The sensor works beautifully, it does the job very nicely, so far I have no complains. Would say much sharper than the pickup sensor for sure. (Project: rotary engine Rx7) thanks diyautotune.

    Was this review helpful to you? 0 of 0 people found this review helpful

  2. 5 out of 5

    Excellent kit
    Fast Shipping
    Great support

    Was this review helpful to you? 0 of 0 people found this review helpful

  3. 5 out of 5

    The better solutionsRobert,from Italy,
    This is the better ,cheapiest solution to drive a Classic europea 4 cylinder engine.
    I install on Classic Opel,20xe,16 e .
    Have about 20 cars runs MS 2, and some of that runs micro,the quickest solutions.
    Thanks DIY,Good device,hope it test cheap!!!

    Was this review helpful to you? 0 of 0 people found this review helpful

  4. 5 out of 5

    Well MadeA very clean installation - fit the v3.0 board perfectly. I won't go back to drilling and filing my own end plates.

    Was this review helpful to you? 0 of 0 people found this review helpful

  5. 5 out of 5

    Huge Upgrade from MS1Very easy to swap out my MS1 processor for an MS2. Much faster and more functionality from 16x16 tables to stepper-style IAC to expanded trigger wheel options. Very happy.

    Was this review helpful to you? 0 of 0 people found this review helpful

Add a review

What did you put into your kit to make it an improvement on the competition?

  • We’ve made sure you have enough pins for all the connectors, plus a few spares. And we have included all three pin sizes, as the Weather Pack pins are not one size fits all – they have three different sizes to get reliable fitment and sealing on different wire sizes. This kit will accommodate 20 to 12 gauge wire.

What is the maximum rated current?

  • At room temperature, Delphi’s maximum current recommendation is 16 amps for 20-18 gauge wire and 20 amps for 16 gauge and above – note that this is often more than the wire can handle. For temperature derating curves, see this page on Delphi’s site.

Questions & Answers

  1. 0 votes
    A

    Crimpers are sold separately in the Tools section of our website.