Search Results for: map sensor
How to MegaSquirt Your Z32 Nissan 300ZX
Application(s): 1990 to 1996 Nissan 300ZX VG30DE and VG30DETT motors with the OEM distributorless ignition. Level of control: Full Standalone EMS– Fuel and Ignition Control The cam angle sensor has often been a bit of an issue for MegaSquirt, but now with MS3’s new V1.1 code, you don’t have to disassemble the CAS for an…
Read MoreHow to MegaSquirt Your Chrysler, Dodge, or Mitsubishi 3.0 SOHC
Using the stock distributor Application(s): This article covers the 1988-1995 Mitsubishi / Dodge / Chrysler 3.0 SOHC V6, as used in K-car derived cars (Daytona, LeBaron, Shadow, Sundance, minivans, and other applications) as well as in the Mitsubishi Diamante and various Mitsubishi trucks. Level of control: Parallel installation — Fuel and Ignition Control. Most users…
Read MoreHow to MegaSquirt Your Chevy LT1, LT4 or L99 with Opti-Spark Ignition
Using MegaSquirt ECUs with the Optispark Ignition System Introduction MS3Pro wiring Internal mods for V3.0 and V3.57 MegaSquirts Wiring for V3.0 and V3.57 MegaSquirts Other ECU functions TunerStudio settings Suggested parts Thanks to “Mobythevan” on hybridz.org for his notes on the settings for MS2! Application(s): All Chevrolet LT1, LT4, and L99 engines with the…
Read MoreHow to MegaSquirt Your BMW E30 325i and Other M20/M30 Applications
MegaSquirt installation on BMW M20 and M30 engines, using the factory crank trigger MSPNP ALERT! Check out our out of the box plug & play solution for 87-92 BMW E30 325i, ready to plug into your factory harness! Typical installation takes around an hour. It’s ready to run this engine out of the box, with no…
Read More
The EFI Tuners Guide Chapter 3 – Garbage In, Garbage Out: The Three Stages of Success
Updated September 2022 by Jerry Hoffmann Chapter 3 – Garbage In, Garbage Out: A properly installed, configured, and tuned Engine Management System makes all the difference (The Three Stages of Success) GIGO: Garbage In, Garbage Out. It’s a pretty simple principal. Whatever you put into this type of project will absolutely play a role in…
Read More
The EFI Tuners Guide – Learn How EFI works!
A practical guide on how to understand and tune your engine/car with Electronic Fuel Injection and Ignition with an aftermarket Standalone Engine Management System Updated September 2022 by Jerry Hoffmann Our EFI Tuners Guide is aimed first and foremost to the DIY EFI installer, configurer, and tuner, this guide will help you understand WHY you…
Read More
Fox Body Mustang: Mass Air Flow vs. Speed Density – Which is better?
Isn’t Speed Density inferior and MAF the best tuning solution on a Fox Body Mustang? Nearly 30 years after Ford stopped production, the Fox Body Mustang remains insanely popular at the race track. There’s probably no single chassis you see more of at the average drag race track, and there is good reason for that!…
Read MoreDIYPNP Documentation for 1987-1992 BMW 325
NOTE: The DIYPNPB55-K Kit has been discontinued as of 8/30/18. 1987-1992 BMW 325 USDM 2.5L M20B25 MT Test Vehicle Details: The vehicle used for drawing up these application docs was a USDM 1987 BMW 325is 2.5L M20B25 with a manual transmission. All factory electronics/ignition system components are in place and the factory wiring harness is in…
Read MoreHow to Use MegasQuirt With the PerTronix Ignitor
If you haven’t already, please read the ‘disclaimer’ at the top of the parent page here. Updated 1/16/2014 Taking control of the timing with a Pertronic Ignitor The PerTronix Ignitor is a small, self contained ignition module that replaces breaker points. PerTronix also offers ready to run distributors that come equipped with the Ignitor. If…
Read MoreDifferent Approaches to MegaSquirt Installation
With all the different MegaSquirt options out there, chosing the right system can be a bit intimidating. The first decision you’ll need to make is the overall approach. Do you want to keep expenses as low as possible by soldering your own kit together? Or would you rather spend less time and more money? Here’s…
Read More