DIYPNP Documentation for 1995 – 1998 Nissan 240SX


1995 – 1998 Nissan 240SX USDM 2.4L KA24DE MT

 

Test Vehicle Details:

The vehicle used for drawing up these application docs was a USDM 1996 Nissan 240SX KA24 with a manual transmission.  All factory electronics/ignition system components are in place and the factory wiring harness is in perfect condition.

Other notes:
All stock sensors were used.

What to buy:

Required:
1- DIYPNPJ88-K Kit.  This is the main DIYPNP Kit including the JAE style 64-pin connector and all components, case, etc.

Optional:
1- Tuning Cable  This is the same DB9 serial tuning cable used in other MegaSquirt applications.
1- USB Adapter  This is a DB9 serial to USB adapter.  The adapter is needed when the laptop or PC you are using does not have a built in DB9 serial port.
1- StimPower  This is a power supply that is normally sold to power a stimulator, but another use is it can be plugged directly into the DIYPNP mainboard to power the ECU directly, allowing you to load the base maps and do limited testing on the ECU prior to installing the ECU in your vehicle.  It is particularly nice to be able to flash the firmware and load your configuration on the bench instead of in the vehicle, and allows for less risk of damaging something on the vehicle due to incorrect settings.
1- PNP_IAT-A or PNP_IAT-S AFM/MAF Delete kit. This is a simple kit with an IAT sensor, wire pigtail, crimp pins to poke into the AFM Connector to run the signal back to the ECU, and a steel or aluminum bung (hence the -A and -S in the part numbers).  Perfect for getting rid of a restrictive AFM/MAF with your DIYPNP install.

What tools you’ll need: Soldering Iron, Solder, maybe some desoldering braid in case you make a mistake.  Small phillips screwdriver.  That’s about it.

 

 

Startup Maps

Base Configuration .msq files to help you get your car fired up safely and quickly.  Ready to tune.

We’re including these maps prior to showing you how to jumper your DIYPNP up.  There’s a reason for that.  The base ignition settings contained in these maps should be loaded on your DIYPNP before you power your car up (with the key) with the DIYPNP installed.  This is to prevent damage to your ignition system in case the default settings are not correct for your vehicle. Note that you can power up the DIYPNP off the vehicle on a power supply connected to the power jack next to the DB15 connector.

So here’s our recommendation–  After you complete basic assembly, Power up your DIYPNP one of two ways.  Either plug a Stimulator Power Supply into the front panel of the box (the easiest way), or, start the Jumper Section below, but only connect the power and ground wires to start with.  That way you can plug the DIYPNP into your factory wiring harness and safely power it from your car.  The third option, if you’ve fully assembled and jumpered your DIYPNP already, is to unplug your coils from their power connectors before plugging the DIYPNP into your factory harness and powering it from there.

Then and only then, you can flash the firmware on your DIYPNP to the MS2/Extra firmware if you haven’t already, and then load the startup map provided to help you get your vehicle started.

Click Here to Download Startup Maps for this Vehicle

Once the vehicle is started, you will need to use the MS2/Extra manuals to set the base timing and begin to tune the vehicle!  This is critical!  Do not drive an untuned vehicle!

DIYPNP Jumper Configuration

This section will cover the standard, basic jumper configuration required to get the vehicle running using your DIYPNP.

Vehicle Information

Market: USDM
Make: Nissan
Model: Sentra
Year: 1996
Engine: KA24DE
Transmission: Manual
Trim:

System Information

Main Board: DIYPNP v1.5
Minimum Code Version MS2Extra 3.1.0

Edge Pin Connections

Main Adapter
IAT 28
CLT 51
TPS SIG 23
O2 SENSOR 46
VR IN +
VR IN –
OPTO IN + 40
OPTO IN –
VR2 IN +
IAC 101
TACH OUT 3
FUEL PUMP 8
INJ1 102, 109
INJ2 104, 107
12V 38
12V
12V
VREF 49
5V
SG 50
SG
GND 10, 19
GND 39, 43
GND 106, 112
GND 118
GND
IGN1 1
IGN2
WLED 14 � L
ALED 13 � H

Pull Ups

Connection Resistance Voltage
ALED
WLED
OPTO+ 470 Ohm 12V
VR2
IAC FB Diode Banded end to 12V

High Current Drivers

Output Enabled To Pin
S1
S2
S3
S4

Knock Circuit

Enabled Sensor + Sensor –

I/O Circuits

Circuit Input From Out Pin To Purpose
Relay 1 38 4 ECCS Relay
Relay 2
Boost
Input 1 21 15 A/C Relay
Input 2

Miscellaneous Jumpers

On Off
OPTO GND
BL/TH X

Notes

Ignition Settings

Spark Mode Basic Trigger
Trigger Angle 112
Main/Return
Oddfire Angle
GM HEI/DIS Off
Use Cam Signal
Ignition Input Capture Falling Edge
Spark Output Going High (Inverted)
Number of Coils Single Coil
Dwell type Standard Dwell
Cranking Dwell 4
Cranking Advance 10
Maximum Dwell 3.1
Maximum Spark Duration 0.7
Spark Hardware Latency 20
Trigger wheel teeth
Missing teeth
Tooth #1 angle
Wheel speed
Second trigger active on
and every rotation of


 

 

Other Changes/Considerations

This section will cover changes that need to be made to the DIYPNP that go beyond the standard I/O jumpering, such as intake valve butterfly activation, on/off VVT activation, or other customizations to address the specific needs of a vehicle.

A/C Controls

In the Jumper Notes above we’ve included jumpers for A/C clutch and fan activation using the ‘Input 1’ circuit.  The Input for the AC system comes in from the A/C switch on ConnectorBoard pin 21.  The output of the “Input 1” circuit gets jumpered to pin 15 on the ConnectorBoard.  This pin will activate the A/C compressor clutch relay and the A/C condensor fan relay.  You will need to leave R14 out of this circuit or cut out R14 if you installed it.

 

 

Sensor Calibration

  • This vehicle does have a variable TPS.  You should calibrate it properly from TunerStudio in the ‘Tools’ menu.  Choose ‘Calibrate TPS’.

    • Make sure the engine is off, and the key is on.

    • With your foot off of the throttle, click the ‘Closed Throttle ADC Count – GET CURRENT’ Button.

    • Put the throttle to the floor.  With your foot fully depressing the throttle, click the ‘Full Throttle ADC Count – GET CURRENT’ Button.

    • Click Close.

  • Calibrate your CLT Sensor and IAT Sensor.

    • Again from TunerStudio, click ‘Tools > Calibrate Thermistor Tables’.  Make sure ‘Coolant Temperature Sensor’ is selected at the top.

      • For the CLT, use the following table with a bias resistor setting of 2490 ohms:

        Temperature    F Resistance In Ohms
        68 2500
        122 800
        194 200
    • Enter these values, and click ‘Write to Controller’.

    • Now you’ll do the same for the IAT.  Select ‘Intake Temperature Sensor’ at the top in the drop down box.

      • For the IAT, use the following table for the stock sensor with a bias resistor setting of 2490 ohms:

        Temperature    F Resistance In Ohms
        68 2500
        122 800
        194 200
    • Enter these values, and click ‘Write to Controller’.  Now click Close to Exit.

  • Finally, you should calibrate your O2 Sensor to the ECU.  To do this, click ‘Tools > Calibrate AFR Table’.

    • Choose your O2 Sensor from the list.  Choose Narrowband for the stock O2 Sensor.  Or select your wideband and the proper configuration of said wideband from the drop-down list.

    • Click ‘Write to Controller’.  Once finished writing, click ‘Close’.

Deleting the MAF

The DIYPNP allows you to disconnect the Mass Air Flow meter since it is not used in the fuel load calculation. When you remove the MAF, you will want to tape up the connector to protect it inside and out if you ever plan to re-use it.  The stock intake air temp sensor is not located inside the air meter so there are no wiring changes to be made.

Intake Air Temp Sensor: If you plan to install a turbo

The stock IAT sensor and location will not be adequate if you decide to run a turbo or supercharger.  For best results, you will want an air-tight seal with the sensor placed in the intercooler piping, after the intercooler and before the throttle body.  The temperature of the air as it enters the engine (not the turbo or supercharger) is what the ECU needs to know.  We offer an IAT kit (sensor and weld-in bung) for either steel or aluminum piping.

Read the Manuals, You are Responsible for your own results!

This Application Doc is intended to assist you in your DIYPNP DIY EFI Installation.  We’ve done a fair amount of research, and actually tested on a similar vehicle to help ensure we can provide the most accurate information possible to make your installation go as smoothly as possible. That said, there are certain things you could do incorrectly, or certain things you could change up, that could cause you to run into issues.  Our tech support department will be glad to assist you working through any issues you might have, please contact us and give us that opportunity and we should be able to work things out for you.

Startup Maps included/attached to this Application Doc is intended only to help you get your engine started so that you can properly tune your engine.  The map will be setup properly for a stock vehicle matching the year/make/model/trim in the ‘Test Vehicle Details’ section at the top of this page.  If you have made any changes to your wiring, your ignition system, or other related components, this map may not be ideal for your vehicle.  You will then need to check and confirm the appropriate settings and properly configure your DIYPNP EMS for your altered vehicle.  Some maps offered may be more completely tuned that others, some may be just setup enough to get the car to fire up and idle with a little help from the throttle.  That’s when the tuning begins.

In short– We’ve provided you with the building blocks for an incredible EMS.  You are however responsible for the implementation and your own successes or lack thereof, but rest assured that we’re here for you and we’re going to do everything in our power to make sure your project is a success.

For more information on configuring and tuning your DIYPNP EMS, and for information on adding and tuning custom MS2/Extra features, read up athttps://www.msextra.com/ms2extra/.  In fact, everyone implementing this system should read that manual from front to back if you really want to harness the power of the DIYPNP EMS.

 

We’d love to hear your feedback on our DIYPNP Application Docs.  Click Here to offer feedback/suggestions!