Cart

Quick Links

Bowling & Grippo

Bowling & Grippo

Showing 1–16 of 19 results

  • MicroSquirt Wiring Harness – 8ft

    $89.00

    Included is an 8' long harness for installing the MicroSquirt on larger vehicles instead of motorcycles and ATVs. Serial cable included.

    Add to cart
  • MS330-K Kit with MapDaddy4

    $509.00

    MegaSquirt-III Engine Management System w/PCB3.0 - Unassembled Kit Part # MS330-K_m4 This MS330-K_BL kit includes everything you will need to build your MegaSquirt-3. The genuine B&G partial kit with the V3.0 PCB, all components in the standard V3....

    Add to cart
  • MegaSquirt-III with PCB V3.0 Kit

    $445.00

    Included is a MegaSquirt-III Engine Management System w/PCB3.0 - Unassembled Kit Part # MS330-K This MS330-K_BL kit includes everything you will need to build your MegaSquirt-3. The genuine B&G partial kit with V3.0 PCB, everything in the standard ...

    Add to cart
  • MegaSquirt 3 EMS System V3.57

    From: $645.00

    MegaSquirt 3 Engine Management System w/PCB3.57 - The MegaSquirt 3 is a drop in daughter card that greatly expands the MegaSquirt's functionality. This model is equipped for basic, batch fire, but can be expanded to add sequential injection and 8 channel ...

    Add to cart
  • MegaSquirt-I Programmable EFI System PCB2.2 – Kit

    $197.00

    MegaSquirt-I with V2.2 Main Board MegaSquirt programmable EFI Engine Management System from Bowling and Grippo. Install fuel injection on anything from a single cylinder lawnmower engine to a fire breathing V12, and anything in between! This kit is eas...

    Add to cart
  • MS230-K Kit with MapDaddy4 Upgrade

    $388.00

    MegaSquirt-II Engine Management System with 3.0 Main Board - UnAssembled Kit; Part # MS230-K_m4 The MS230-K kit includes everything you will need to build your MegaSquirt-2. The genuine B&G partial kit with PCB3.0 (note: BIP373 coil driver is sold...

    Add to cart
  • MegaSquirt-II Programmable EFI System PCB3.0 – Kit

    $324.00

    MegaSquirt-II Engine Management System with 3.0 main board - Unassembled Kit with Black Case; Part # MS230-K The MS230-K kit includes everything you will need to build your MegaSquirt-2. The genuine B&G partial kit with PCB3.0, the Bill Of Materia...

    Add to cart
  • MicroSquirt Module V2.2

    $284.00

    MicroSquirt Module is a credit card sized engine management board! This board packs all the features of the MicroSquirt except high current ignition drivers into a 3.5" x 2.4" PCB, with all components installed. This tiny ECU opens up unprecedented possib...

    Add to cart
  • PKIT – MegaSquirt-II PCBv3.0 Partial Kit

    $230.00

    MegaSquirt-II PCBv3.0 Partial Kit PCBv3.0, MegaSquirt-II daughterboard and MPX4250 MAP Sensor for building a MegaSquirt-II PCB 3.0 ECU. Complete Bill of Materials (parts listing) and assembly instructions can be found HERE . Click HERE for comp...

    Add to cart
  • MegaSquirt-III Daughterboard Kit

    $230.00

    Upgrading your MS1 or MS2 to the latest MS3 has never been easier with this processor replacement! We've packaged the MS3 daughter board with 2 of the 40 pin sockets, so it will match up with our cases (required for upgrade) which have cutouts for the SD ...

    Add to cart
  • MegaSquirt-III MS3X Expansion Card & Connector Kit

    $110.49

    Put this small circuit board in your MegaSquirt-III to unlock its full potential! This board installs in the MS3 case with no soldering; just connect it with the included ribbon cables. Install the MS3X board to add this whole list of inputs and outputs t...

    Add to cart
  • PKIT – GPIO Board Partial Kit

    $178.00

    This is a very basic and incomplete starting point for building a GPIO (General Purpose Input/ Output) kit. It includes the main board, all SMD components soldered on, AMPSeal connector, and all the AMPSEAL pins, each crimped to a short length of TXL wire...

    Add to cart
  • CPU – MegaSquirt-II Daughterboard

    $136.00

    MegaSquirt-II Daughterboard For upgrading your Megasquirt-I ECU, or replacement of your damaged MegaSquirt-II daughterboard.  MS2 daughter cards are for use only with genuine Bowling & Grippo MegaSquirt mainboard PCBs. This is the latest version o...

    Add to cart
  • PKIT – MegaSquirt-I PCBv3.0 Partial Kit

    $132.00

    MegaSquirt-I PCBv3.0 Partial Kit PCBv3.0, MegaSquirt-I CPU and MPX4250 MAP Sensor for building a MegaSquirt-I PCB 3.0 ECU. Complete Bill of Materials (parts listing) and assembly instructions can be found HERE . Click HERE for complete MegaSquirt-...

    Add to cart
  • PKIT – MegaSquirt-I PCBv2.2 Partial Kit

    $115.00

    MegaSquirt-I PCBv2.2 Partial Kit PCBv2.2, MegaSquirt-I CPU and MPX4250 MAP Sensor for building a MegaSquirt-I PCB 2.2 ECU. Complete Bill of Materials (parts listing) and assembly instructions can be found HERE. Click HERE for complete MegaSquirt-I ...

    Add to cart
  • CPU – MegaSquirt-I CPU

    $36.99

    MegaSquirt-I CPU; Motorola 68HC908 microprocessor loaded with standard B&G MegaSquirt-I firmware version 3.0. This part is discontinued and available while supplies last. For use with any MegaSquirt PCB version 1, 2.2, 3.0, 3.57...

    Add to cart