Cart

Quick Links

MS3Pro Gen1 with 8' wiring harness DISCONTINUED
MS3Pro Gen1 with 8' wiring harness DISCONTINUED
MS3Pro Gen1 with 8' wiring harness DISCONTINUED
MS3-Pro Standalone ECU
Black box for MS3Pro ECU with wiring harness
MS3-Pro Standalone ECU
MS3-Pro Standalone ECU
MS3-Pro Standalone ECU

MS3Pro 1st Gen Standalone ECU with 8′ Wiring Harness

5 out of 5 based on 3 customer ratings
(3 customer reviews)

-

DISCONTINUED – see details below

SKU: MS3Pro-PKG1 Category: Brands: ,

Description

IMPORTANT PRODUCT UPDATE**  MS3Pro Gen1 has been discontinued and superseded by MS3Pro EVO effective May 1, 2017.  This product page, including documentation, downloads & product FAQ tabs below, remains active for archive purposes.  

Compare MS3Pro Gen1, EVO & ULTIMATE System I/O and Features

Purchase MS3Pro EVO Engine Management System

This package contains MS3Pro Gen1 Standalone ECU, all tuning cables, software & manual on a USB drive, and 8′ wiring harnesses.  The MS3Pro Gen1 can be used with most factory or aftermarket MAP/MAF sensors, allowing for Speed Density, MAF based, or Alpha-N (TPS Based) control, as well as a variety of blended algorithms for special purposes.  We offer MAP Sensors separately as well.

MS3Pro Gen1 Features:

  • VE based tuning
    • No Static PW fuel tables with stacks and stacks of ‘correction tables’ required.
    • Very simple/logical approach to calibration minimizes tuning time required!
  • Speed Density, Alpha-N, MAF based tuning & blended algorithms
    • ITB Mode – blends SD and Alpha-N for excellent drivability with naturally aspirated, multiple throttle applications!
    • Custom blended strategies supported, mix/blend strategies to suit any engine
    • Fuel and spark advance algorithms can be set set independently
  • Up to 12 sequential saturated fuel injector outputs
  • Up to 12 cylinder sequential support
  • Any unused injector outputs can be used as high current digital or PWM outputs
  • Up to 8 sequential logic level ignition outputs
    • Supports single or dual coil distributor, wasted spark, and coil per plug
  • 2D or 3D Table Views
  • The tuner can toggle between 2D or 3D table views with a single click
  • Individual cylinder fuel & spark trim tables
    • Per-cylinder, table based corrections for both ignition timing and fueling needs on a cylinder by cylinder basis. Correct for manifold airflow differences and fine tune each cylinder to perfection!
    • O2 sensors can be assigned per cylinder, allowing for perfect tuning and closed loop correction on a per cylinder basis
  • Table Switching
    • 2 sets of user configurable tables for fuel, spark advance, and boost tables
    • Dual Fuel Support
    • Beyond table switching, adds control of 2nd fuel system (pump and injectors), and adds 2nd settings for injector characterization; fuel stoichiometric point; priming, warmup, cranking, and afterstart settings; alternate acceleration enrichment tables; boost tables; and overboost protection settings.
  • VVT Control (4 channels)
    • Open loop VVT control for 2-position camshafts
    • Closed loop control for fully variable camshafts
    • Controls up to 4 total VVT camshafts
  • Generic Wheel Decoder allows for support of nearly any standard trigger/aftermarket trigger pattern. 60-2, 36-1, 8-1, 4-1, pretty much anything!
  • Ignition Systems Supported:
    • GM LS 24x
    • GM LS 58x
    • GM 7x
    • Toyota/Lexus 2JZ VVTi
    • Ford EDIS
    • Ford Zetec VCT
    • Chrysler 420A/Neon
    • Chrysler New Hemi 36-2+2
    • Dodge Viper V10
    • Subaru 6/7
    • Subaru 36-2-2-2
    • Mitusbishi 6G72
    • Mitsubishi 4G63
    • GM OptiSpark
    • Nissan SR20
    • Nissan RB25
    • Nissan VQ35DE
    • Nissan QR25DE
    • Yamaha YZF1000
    • Honda TSX/D17
    • Honda KA24A2
    • Honda RC51/S2000
    • Mazda Miata NA
    • Mazda Miata NB1 and NB2 (VVT)
    • Harley Davidson 32-2 V-Twin (uses MAP for phase detection)
    • Not a complete list — Many more supported trigger wheels
  • Support for oddfire and evenfire engines
  • Capable of controlling evenfire, oddfire, piston, rotary, and even radial engines
  • Fuel Only Mode
  • Disables ignition output features for control of fuel injection only
  • Internal SDCard high-speed data logging
    • No need for external datalogger!
    • 8GB standard memory. Easily expandable to 16GB
    • Real time clock calendar system for time and date stamped datalogs
    • Up to 28 channels at 100hz
    • No need to remove SD-Card to pull logs, pull them straight across the serial/USB cable to your laptop!
  • Traction Control – Multiple Strategies
    • Perfect Run (VSS over time)
    • Perfect Run RPM (Slew Control for classes where VSS is not allowed)
    • VSS % slip (compares front to rear or driveshaft speed)
    • Configurable Responses
      • Timing retard/cut
      • Fuel Adder
      • Nitrous Cut
      • Boost Reduction
  • E85 flex fuel sensor input
    • Extremely configurable for excellent performance and drivability regardless of fuel gasoline versus ethanol content.
    • Compatible with easy to find GM flex fuel sensor
    • Configurable flex blend curve allows blending of fuel tables, spark advance tables, afr target tables, alternate start and warmup settings, boost and overboost tables, and acceleration enrichment settings based on the exact concentration of ethanol in fuel
  • Compatible with YOUR wideband O2 controller.
    • You choose the wideband controller you want without being locked down. From the super cost effective to the mid-range, to full lab grade capability.
  • Long Term Fuel Trim
  • OE Style automatic fuel trim to allow for changes in engine over time
  • High Power Time Enrichment
  • Allows for richer mixture after extended time in high power
  • Helps control cylinder and piston temperatures
  • Fully user configurable
  • Multiple Acceleration Enrichment Strategies
    • Basic time based and accel pump style AE
    • Advanced wall wetting model based (X-Tau and EAE) acceleration enrichment options
  • Staged Injection Control
  • Seamless transition to 2nd stage injectors for high power applications
  • Multiple user configurable strategies
  • Nitrous control strategies
    • 2 channels of configurable staged or progressive control
    • Supports wet or dry nitrous systems
    • Add fuel, pull timing, etc.
  • Three-step rev limiter with flat shift
    • Burnout Limiter
    • Launch Limiter
    • Redline Limiter
    • Line lock output
    • Flat Shift allows for No-Lift Shifting (holds RPM between shifts)
  • Trans Brake and Bump Box Control
  • No need for a separate box!
  • User configurable settings and reactions
  • Advanced Launch Control strategies
  • Digital switch based arming
  • Wheel speed based launch arming for rolling starts
  • Configurable timing retard after launch
  • Pit Lane Limiter
  • Speed limiter for pit lane, reduces engine power by spark retard/cut or fuel cut
  • Can limit based on VSS or RPM if no VSS input is available
  • Rally style turbo anti-lag with rotational idle
  • Allows cyclic fuel and spark cut
  • Controls idle valve and configurable outputs for external fuel or air supply
  • Boost Control – Multiple open & closed loop strategies
    • Table based open loop (DC solenoid control)
    • Table based closed loop (Target specific boost pressures by load/rpm)
    • Switchable boost tables for high/low boost options at the flip of a switch
    • Boost by Gear
    • Boost by Speed
  • Sequential shift spark cut
  • Configurable spark and fuel cut during shift
  • Solenoid output control for air shifter/drag application
  • Automatic shift point mode
  • Configurable per gear delay
  • Idle Control – Multiple open & closed loop strategies
    • Simple On/Off Idle Valve
    • PWM 2 or 3 wire valves
    • Stepper Motor 4 or 6 wire valves
  • Water and Methanol Injection
    • Configurable to use a variety of water/meth pumps
    • Table based injection allows for variable water/meth injection based on load and rpm
    • Low fluid level detection safety measures
  • Fuel Pump Control
    • “On/off” control of single or multiple stage pumps
    • PWM control of OE variable speed/pressure pumps
  • Intelligent Knock Detection and Response – 2 channels
    • Dual DSP based knock inputs with bandpass filters and dynamically adjustable gain
    • Noise threshold based
    • Windowed monitoring allows for detection of which cylinder knock occurred on
    • Adjustable ignition retard (course and fine responses)
    • Knock correction per cylinder (sequential ignition must be enabled)
  • Multiple Engine Protection and fault mode strategies
    • Check Engine Light activation (solid and flash codes supported)
    • Low Oil Pressure Warning System (illuminates CEL)
    • Limp Home Mode
    • Set low/high limits for all major sensors and activate engine limp mode or shut down responses
      • Water/Meth Injection Low fluid Level
      • IAT
      • CLT
      • TPS
      • MAP
      • Battery Voltage
      • Wideband O2 / AFR Safety
      • Sync Loss
      • EGT
      • Flex Fuel
      • Intelligent Knock Detection and Correction (see relevant topic above for more info)
  • Generous spare I/O for any standard/custom I/O needs
    • Configurable On/Off (digital) and PWM outputs
    • Control any relay controlled device or solenoid
    • Fan Control (multiple)
    • Intercooler cooling spray (CO2/etc)
    • Torque Converter (TCC) Lockup
    • Auxiliary Fuel Pump
    • Multipurpose/Generic Closed Loop Control Outputs
  • Spare analog inputs for external sensors
  • Supports standard automotive temperature or pressure sensors
  • Air Conditioner Control with feed-forward Idle-Up
  • Proactively increases idle vale duty cycle (PWM valves) or number of steps (stepper valves) before activating A/C compressor
  • Automatic compressor shutoff at programmable throttle position or RPM thresholds
  • Automatic cooling fan activation with A/C, user configurable
  • Cooling Fan Control
  • Programmable fan on and off activation points
  • Can be configured to run fan with engine running only, or when engine is running and not running
  • Feed-forward idle up for use with large, high demand fans
  • Configurable fan deactivation based on TPS or VSS
  • Alternator Field Control/Voltage Regulation
  • Multiple open and closed loop strategies
  • Configurable voltage and temperature monitoring
  • Separate target voltages for afterstart, normal operation, over run, and WOT
  • Warning lamp output if voltage is above or below target
  • Comprehensive Test Modes
  • Test all outputs for proper functionality and verify wiring before starting the engine
  • Controls all fuel injector outputs, ignition outputs, idle valve, and general purpose outputs
  • Outputs can be tested for on & off or PWM pulse functionality
  • Injector and spark disable mode, allows checking for suspected problematic cylinder by electronically preventing combustion event
  • CAN Support for I/O expansion – virtually limitless I/O capability!
    • Up to 16 EGT inputs via CAN Expansion
      • Add fuel/engine shutdown capable
  • CAN Support for 3rd party dash devices
    • Currently offers support for RacePak, AIM, Race Technology, Traqmate, and Race Capture.
    • Pre-defined “simple” as well as fully configurable CAN broadcasting modes
    • Standard 11-bit message headers
    • Allows for simple integration with any 3rd party devices
  • Android Compatible
    • Use your Android phone or tablet as your dashboard or datalogger
    • Allows accelerometer and GPS data overlaid on your datalogs
      • Requires Android device and serial to bluetooth adapter, not included
  • Self Calibration
    • VEAnalyze Live feature is capable of automatically tuning fuel (VE) tables in real time
  • Fully Enabled
    • MS3Pro Gen1 comes fully loaded and fully enabled, there are no additional features to “unlock” or hidden up-charges to gain access to any functionality.
  • Compact, Efficient & Robust Design
    • Small form factor, approx. 7″ x 4″ x 2″, only weighs about a half a pound!
    • Circuitry optimized for efficiency, low power usage, and no generation of heat
  • No Dark Current!
    • No power draw when system is off. MS3Pro Gen1 will not discharge your expensive race battery when your vehicle is in storage.
  • Field Upgradeable Firmware – enable newly added features with a simple firmware update!
    • Firmware is constantly under development and updates are easy to load via simple software interface.

 

*All parts are sold for OFF ROAD RACE-ONLY, ground-vehicle use only. Aftermarket EFI/EMS systems are not for sale or use on pollution controlled vehicles. Alteration of emission related components constitutes tampering under the US EPA guidelines and can lead to substantial fines and penalties. Your state/district may also have specific rules restricting your tampering with your vehicle’s emissions system. In short, as stated before, our official policy has to be RACE or OFFROAD USE-ONLY in ground based vehicles ONLY.

Customer reviews

Rated 5 out of 5 stars
3 reviews
4 stars 0 0 %
3 stars 0 0 %
2 stars 0 0 %
1 star 0 0 %

3 reviews for MS3Pro 1st Gen Standalone ECU with 8′ Wiring Harness

Only logged in customers who have purchased this product may write a review.

Complete MS3Pro 1st Gen User Manual (1.5.0 Firmware) [PDF ]

 

 

Drivers for the USB connection can be found on the FTDI website.

The latest firmware & tuning software, as well as previous version archive, can always be accessed at  https://www.ampefi.com/downloads/

Compare MS3Pro 1st Generation, EVO & ULTIMATE I/O and Features

What is in the box?

  • MS3Pro 1st Gen Standalone EFI Controller
  • 8′ “Flying Lead” wiring harness
  • USB and serial communications cables
  • 4 resistor pills for fine tuning crank/cam inputs on some installations
  • Includes TunerStudio registration code
  • USB drive (for software/documentation)

How big is the ECU?

  • The MS3Pro measures approximately 7″ long (including the mounting ears), 4″ wide, and 2″ tall including the mating connectors. Not including the connectors, the case itself is 1″ high.

What are the part numbers and where do I find User Replaceable Fuses?

Where is this product manufactured?

  • This product is manufactured in Gainesville, Georgia, USA.

What is the warranty on the MS3Pro?

  • It carries a one year warranty against manufacturing defects.

How watertight is the box?

  • The case uses an o-ring seal and sealed connectors to ensure it is completely splashproof, and will keep water out if completely immersed up to a few inches for a few  minutes (which normally shouldn’t happen, right?).  If you need further water submersion resistance that can be accomplished with a small bead of silicone just inside/outside of the o-ring.

Questions & Answers

    I have an MS3 Pro with the plug and play harness and I want to hook my LM2 into it to run. I was previously speaking with Matt and he told me I could hook it up to the 02 plug and he gave me the instructions to do so. Do you have a plug that I can wire into the LM2 side so I can hook it into the MS3 Pro? Thanks for your help, Brian.
  1. 0 votes
    Q I have an MS3 Pro with the plug and play harness and I want to hook my LM2 into it to run. I was ...... Read more
    Asked by Brian
    A

    It's currently not listed on the website. Please contact us directly if you want to order one.

Only registered users are eligible to enter questions