Showing 321–336 of 356 results
-
Fuel Injector Pigtails – Bosch EV1
$8.00Bosch Style Fuel Injector Plug with 6" Wire Pigtail Fits a wide variety of cars that use Bosch injectors. This connector incorporates seals on the pins for maximum corrosion resistance and the spring wire has a quick release ability - just squeeze it a...
Add to cart -
Fuel Injector Pigtails – Bosch EV6
$10.00EV6 Style Fuel Injector Connector with 6" Wire Pigtail Fits many applications; among them several GM applications and the Dodge/Plymouth Neon/Charger/Challenger and others. The wire used is 18 gauge GXL high temperature automotive wire.
Add to cart -
Coil Driver Kit
$10.99Note: This part supersedes the Bosch BIP373. OnSemi EcoSPARK IGBT, perfect for use as a high current ignition driver and can be used as Q16 in your v3.57 or v3.0 MegaSquirt build. This is the same high current ignition driver as used in many of our...
Add to cart -
Bosch BIP373 Coil Driver Mod Kit
$10.00Note: This has been replaced by our Coil Driver Kit. The power transistor that Bosch uses in their own ECUs is now available to you! This is a 'mod kit' for installing a BIP373 in a Megasquirt, or replacing an older or damaged VB921 with the much impr...
Read more -
PCB V3.57 and V3.0 HEI Input Mod Kit
$9.99This mod kit can be used with MS1 and MS2. It's intended for the V3.57 boards, but can be used with the V3.0 as well; you just have to remove the XG1-XG2 and the TachSelect-OptoIn jumpers and replace them with the included header pins. The kit includes on...
Add to cart -
DLP-TXRX Internal USB/Serial Adapter
$31.00DLP-TXRX Internal USB/Serial Adapter This adapter is perfect for converting your Megasquirt from the standard DB-9 serial connection to the USB connection common on newer laptops. The DLP-TXRX can be used on the following MegaSquirt products: MS1 ...
Add to cart -
USB Tuning Cable
$7.50USB A to Mini B cable. Use this with the following products: MS3Pro EVO MS3Pro Ultimate CAN-EGT MS1 or MS2 V2.2 or V3.0 modified with DLP-TXRX mod kit We include this cable with MS3Pro EVO & Ultimate. Does not fit MS3 V3.0 or V3.57.
Add to cart -
Metal DB37 Cover with Hardware & Gaskets
$10.50Metal DB37 Cover with Hardware and Gaskets This Metal DB37 cover is perfect for building up your own Megasquirt wiring harness or relay cable connector.
Add to cart -
DB37 Metalized Plastic Backshell
$2.99This is the 937GME-ND metalized plastic backshell cover included in our basic Megasquirt kits. It's not the same as the massive AMP metal cover used on our harnesses (that's sold on its own under wiring components), but it is cheap and effective if you're...
Add to cart -
DB37 Solder Cup Connector
$3.00DB37 female solder cup connector, as included in our Megasquirt and relay board kits. Use this if you're making a new harness and prefer a soldered connection. This is the connector only; the backshell is sold separately.
Add to cart -
MegaSquirt PWM IAC Valve Control (TIP120) ‘Mod-Kit’
$9.99These are the parts needed for the 'TIP120 PWM idle valve' mod. If you are installing all optional components on the v3 heat sink (leaving no extra space for this transistor there) then you can drill a hole in your case and use it as your heat sink or a...
Add to cart -
MegaSquirt Pull-up Resistors Mod Kit
$3.99Six 1k 1/4w resistors, and four 470ohm 1/4w resistors. Perfect for use as 'pullup resistors' for your MS ECU modding needs. These can be used for several of the mods described in some of our car-specific install articles listed on the site. NOTE: Th...
Add to cart -
MegaSquirt Relay Control Mod Kit (VTEC, TVIS, Fans)
$9.99Modkit used to build a relay control circuit, suitable for switching a relay on/off and controlling fans, VVT, VTEC, TVIS, anything a relay can control. Usable on the PCBv3.0, v3.57 or PCBv2.2 ECUs Information and an example of how to implement this...
Add to cart -
MegaSquirt Ford Bias Resistors Mod Kit
$3.99This is a simple two-part kit with two 1/4w 27kohm metal film resistors to replace R4 and R7 in any MegaSquirt PCB2.2 or PCB3.0 ECU. This will allow for use of the stock Ford temperature sensors without recalibrating the MegaSquirt for the Ford sensors. N...
Add to cart -
IAT Sensor Kit – Steel Bung
$34.99Streamline your AFM/MAF removal process with our kit designed for AMP|EFI ECUs. When removing the air flow meter, you'll often need to relocate the air temperature sensor, as many MAF units have it built in. This kit provides everything you need to instal...
Add to cart -
IAT Temperature Sensor Kit – Aluminum Bung
$34.99Simplify your AFM/MAF removal process with our comprehensive kit designed for use with AMP|EFI ECUs. When removing the air flow meter, you’ll often need to relocate the air temperature sensor, as many MAF units have this sensor built in. Our kit provide...
Add to cart