- Sorry, this product cannot be purchased.
Showing 1–16 of 25 results
-
Replacement 277-1255-ND 10 Position Screw Terminal
$6.50Replacement 10 position block for relay board.
Add to cart -
Replacement 277-1249-ND 4 Position Screw Terminal
$4.99Replacement 4 position block for relay board injector power terminals.
Add to cart -
40 Pin DIP Socket AE7240-ND
$3.99Replacement AE7240-ND 40 pin socket. Used for the main board processor socket, as well as extension spacers on the MS3 daughter boards.
Add to cart -
Replacement D-Sub Thumb Screw
$3.00Replacement thumb screw, as used on our wiring harnesses. Sold individually.
Add to cart -
CP-102A-ND Power Jack Connector
$3.00Replacement CP-102A-ND power jack connector. 5.5 mm OD, 2.1 mm ID. Used on the Stimulator, JimStim, and DIYPNP to connect to a power supply.
Add to cart -
DIYPNP Replacement Coil Driver Heat Sink
$2.00TO-220 heat sink as used on coil drivers for the DIYPNP. V1.1 DIYPNPs also used these for the voltage regulator, boost control, and a few other functions.
Add to cart -
8 Case Screws
$2.00This is a packadge of 8 replacement case screws. As used on the regular MegaSquirt cases and VVTuner.
Add to cart -
DB15 Solder Cup Connector
$3.00DB15 female solder cup connector, as included in our V3.57 setups, DIYPNP, and VVTuner. Use this if you're making a new harness and prefer a soldered connection. This is the connector only; the backshell is sold separately.
Add to cart -
Jumper 10-Pack
$7.4910-pack of wire jumpers in 5 colors. These fit 0.1" headers and are used on the JimStim to make connections for testing additional circuitry. There are several other uses for them too.
Add to cart -
DB15 Metalized Plastic Backshell
$3.00Metalized plastic backshell for the DB15 spare I/O connector, as used on our DIYPNP, VVTuner, and V3.57 boards.
Add to cart -
Y Vacuum Fitting
$2.001/8" vacuum Y-fitting, as included in the MSPNP and Mustang plug and play packages. This is made of clear polycarbonate. Maximum pressure 125 psi. This plastic is tough enough to take 275 degree F engine temps, and won't crack even if exposed to Siberian ...
Add to cart -
Replacement Relay Board Relay
$7.99Single replacement Tyco relay for the relay board. This is a pretty standard relay (Mini-ISO) and may fit many OEM fuse boxes as well. SPST contacts, rated for 12 volts and 30 amps. Does not have a mounting tab, so trying to use it with spade terminals is...
Add to cart -
DB37 Solder Cup Connector for MS3X
$6.50To make sure you can't accidentally switch the upper and lower harnesses, the MS3X harness uses a male DB37 connector instead of a female one. We've packaged a DB37 male solder cup connector and a metalized plastic backshell for your MS3X builds. See t...
Add to cart -
Bulkhead Vacuum Fitting
$2.49Bulkhead fittings, just like those included in our V2.2 kits and MapDaddy. It's made from black nylon, fits 1/8" vacuum line on both sides, and measures about 1 1/4" long. Use to replace broken fittings, or if you're running your MAP sensor or boost gauge...
Add to cart -
Bulkhead Vacuum Fitting – 1/8″ to 1/8″
$2.50Bulkhead fittings, just like those used in the MSPNP Gen 2 and MS3Pro PNP line. It's made from black nylon, fits 1/8" vacuum line on the outside and 1/8" inside, and measures about 1 1/4" long. Use to replace broken fittings, or if you're running your MAP...
Add to cart -
Replacement DB37 Female PCB Mount Connector
$5.99Replacement DB37 female PCB mount connector, as used on Stimulator kits. Could also be used on boards that plug into a MegaSquirt such as the TBI or TPI adapter board.
Add to cart