Cart

Quick Links

Ford Mustang 8693 MegaSquirt Gen2 Plug and Play
Ford Mustang 8693 MegaSquirt Gen2 Plug and Play
Ford Mustang 8693 MegaSquirt Gen2 Plug and Play
Ford Mustang 8693 MegaSquirt Gen2 Plug and Play
Ford Mustang 5.0 SN95 1994-1995 MSPNP Gen2 Plug and Play ECU

Ford Mustang 5.0 SN95 1994-1995 MSPNP Gen2 Plug and Play ECU

4.5 out of 5 based on 2 customer ratings
(2 customer reviews)

$869.99

-

Frequently purchased together

Innovate Standalone Gauge Kit with LC-2 & Blue DB Gauge - 3795

USB to Serial Adapter - Trouble Free!!

**Sold Out** Perfect Tuning Universal Gauge MS3Pro, MS3, MS2

Out of stock

Description

Ford Mustang SN95 1994-1995 MegaSquirt Gen2 PnP Plug and Play Standalone Engine Management System is compatible with the following:

  • 1994-1995 SN95 Ford Mustang 5.0 – Manual transmission

Easy to Use and Install!  (Can be reconfigured for some other EEC-IV (EEC4) equipped cars/trucks with internal jumper changes by special order – contact DIYAutoTune for details)

Ford Mustang SN95 1994-1995 MegaSquirt Gen2 Plug and Play Model #EEC4B8 Features:

  • Fully Plug and Play Installation – No wiring required for basic functionality.  Average install time is under 1 hour!
  • 5.0 HO base maps is pre-loaded to help your engine start on the first turn of the key
  • Real time tuning and data logging with a laptop connection
  • Supports most aftermarket wideband sensors
  • Uses internal MAP sensor – can be used on both cars with factory MAF or speed density
  • Mounts in the stock location – case is specifically designed to use factory mounting points

Fully Tunable Engine Control!

  • 16×16 Fuel Tables allow high resolution tuning
  • Bank to bank fuel control
  • 12×12 Ignition Tables
  • Multiple Acceleration enrichment strategies
  • Closed Loop Idle Speed Control
  • Retains air conditioner function
  • Onboard high impedance injector drivers
  • Allows removal of stock MAF sensor, if so equipped
  • Programable fan control

Advanced Feature Set (Included!)

  • 12×12 Air Fuel Ratio Target Tables for use with wide band O2 sensor for precise tuning and table trim
  • Built-in 2-step rev limiter / launch control with flat shift
  • Real time barometric correction
  • Internal 4-bar MAP sensor reads up to 44PSI of boost
  • Overboost protection
  • Closed loop boost control (Requires boost solenoid kit)
  • Knock sensor input with adjustable sensitivity
  • Headphone output for knock sensor – listen for knock while you tune!
  • Table switching input. Change fuel and spark maps on the fly for different fuels, nitrous activation, etc.
  • Input for flex fuel sensor – switch between E85 and gasoline on the fly!
  • CANBus connector allows interconnection of other MegaSquirt-compatible devices for additional functions (EGT Input, Automatic Transmission Controller, Additional Sensors)…..the possibilities are limitless!

What you get in the box:

  • Ford Mustang SN95 1994-1995 MegaSquirt Gen2 Plug and Play ECU
  • MSPNP RS232 serial tuning cable, 6′ (USB adapter sold separately, if needed)
  • Tuning Software and Documentation USB Stick with TunerStudio Lite
  • 6′ Vacuum Hose for MAP Signal and ‘T’ fitting

Note: Although there is a paid upgrade to TunerStudio, it is not needed to tune this ECU. The free version included on the USB Stick can access all the features and tables of the MegaSquirtPNP. The paid version of TunerStudio simply adds tuning and analysis software, such as VE Analyzer Live to tune the fuel tables based on wideband O2 feedback (requiring a wideband O2 sensor and controller, sold separately). It also unlocks the ability to use customized dashboards, such as our MSPNP2 Dash, which is designed specifically to help make tuning your new build intuitive and easy!

Customer reviews

Rated 4.5 out of 5 stars
2 reviews
3 stars 0 0 %
2 stars 0 0 %
1 star 0 0 %

1 reviews with rating of 4 stars (1 of 2)

(Show unfiltered results)

2 reviews for Ford Mustang 5.0 SN95 1994-1995 MSPNP Gen2 Plug and Play ECU

Only logged in customers who have purchased this product may write a review.

Is this all that I need to get started tuning my Mustang?

  • The only other potential must-have is that if your laptop doesn’t have a 9 pin serial port, you will need our USB to serial adapter to connect to this unit. However, there are several other things you may wish to add to use this unit to its full potential.

Does the MSPNP Gen 2 support sequential injection on ’94-’95 Mustangs?

  • The MSPNP Gen 2 has a maximum of four fuel channels, so it is configured for bank to bank fueling in this application.

What if I have an automatic transmission?

  • ’94-’95 Mustangs had transmission control built into the ECU. It would be possible to use a wire in transmission controller to run the transmission separately, but the transmission control would not be plug and play.
  • If you are using a non-stock transmission without computer control (such as a C4, C6, or Powerglide), you can use this ECU without any trouble.

Where’s the serial port on this one?

  • The 9 pin serial port on the other MSPNPs did not clear the stock mounting bracket on this car, so we have opted to use a 2.5 mm barrel connector for the serial cable for this model.

Questions & Answers

    I have a 1995 Mustang GT with some mods but mostly stock, why would I want to install this and what will it do performance wise? I apologize, I'm not too experienced with them.
  1. 0 votes
    Q I have a 1995 Mustang GT with some mods but mostly stock, why would I want to install this and wh...... Read more
    Asked by Steve
    A

    This is a tunable race ECU that replaces the factory controller. It is intended for competition vehicles that are not street legal. It may be overkill for a mostly stock car, but allows for tuning for a wider range of modifications than a stock ECU can readily accommodate. This unit also allows for some racing electronics features such as a launch rev limiter and boost control.

    This device isn't intended to add power per se, as much as to allow you to get all the power you can get out of modifications you've added. The further the car is from stock, the more potential gains you have.

  2. I already have an auto meter wideband setup will it work with this ECM or will I need to buy the innovate setup
  3. 0 votes
    Q I already have an auto meter wideband setup will it work with this ECM or will I need to buy the ...... Read more
    Asked by Lawrence
    A

    Yes, it works with Auto Meter widebands as well. You'll just need to enter the appropriate calibration data in TunerStudio.

  4. I bought a innovate lc-2 to use with the MegaSquirtPNP. What pin on the ECU connector do I hook it up the lc-2 to? Also what analog wire is best to use on the LC-2 should i use for the wide band signal?
  5. 0 votes
    Q I bought a innovate lc-2 to use with the MegaSquirtPNP. What pin on the ECU connector do I hook i...... Read more
    Asked by Tom Stahura
    A

    The easiest way to wire this up is to connect the analog output to pin 21 of the 26 pin options port on the MSPNP, and disconnect the stock sensors.

    If you are not using the LC-2 with a gauge, use the #1 (yellow) analog output wire. If you are using a gauge, you will need to use separate analog outputs for the gauge and the ECU, and program both to use the same 0-5 volt output curve using the LM Programmer utility.

  6. Dose it plug into the stock harness or do I need to build/buy one that fits.
  7. 0 votes
    Q Dose it plug into the stock harness or do I need to build/buy one that fits.
    Asked by Perry Andrews
    A

    This unit plugs into the stock harness.

  8. Does it matter if I have already bought my PROm massair to match my injectors?
  9. 0 votes
    Q Does it matter if I have already bought my PROm massair to match my injectors?
    Asked by Jay
    A

    You will need to adjust the tune for the larger injectors.

    This ECU is normally set up for speed density, although it is possible to reconfigure it to support a MAF if you have a voltage vs flow curve for the one you are using.

  10. 95 megasqurirt works for 93 models?
  11. 0 votes
    Q 95 megasqurirt works for 93 models?
    Asked by lewis
    A

    Some of the injectors are connected to different pins on the SN95 Mustangs. We weren't able to build one plug and play that fit both at the same time.

  12. Does this work with a MSD magnetic pickup distributor instead of the ford TFI?
  13. 0 votes
    Q Does this work with a MSD magnetic pickup distributor instead of the ford TFI?
    Asked by Gregory Kendall
    A

    The MSPNP is preconfigured specifically for stock Ford sensors and their aftermarket equivalents. It will not support the MSD two wire magnetic pickup, but it will work with MSD TFI type distributors.

  14. I have a stock 1995 Mustang GT and am planning several engine upgrades/modifications. I am new to the ECU tuning world but would like to go with the DIYAUTOTUNE Megasquirt device since I plan on using this manufacturer for other projects as well due to my perception that you are one of the industry standards. My question has to do with all current functions on the stock car such as cruise control. Will the Megasquirt PNP for this vehicle support the cruise control and all other devices the stock ECU controls? This will be my first time learning tuning. Thank you for your time.
  15. 0 votes
    Q I have a stock 1995 Mustang GT and am planning several engine upgrades/modifications. I am new to...... Read more
    Asked by Frank Johnson
    A

    Cruise control is not run through the ECU on these cars, so it will keep working as normal. The only thing the MSPNP won't control is some emissions functions.

  16. CAN THIS RUN A 351W OUT OF A FORD TRUCK ABOUT THE SAME YEAR 96ISH THE ECU OUT OF THE TRUCK IS A (F4TF-AHB) IF IT MATTERS. TRUCK WAS A STANDARD TRANS
  17. 0 votes
    Q CAN THIS RUN A 351W OUT OF A FORD TRUCK ABOUT THE SAME YEAR 96ISH THE ECU OUT OF THE TRUCK IS A (...... Read more
    Asked by ZACKARY CONN
    A

    Sorry, a 1996 model would have been an EEC-V and uses a different connector. The wiring harness would not even physically fit. The Mustang MSPNPs can work with many of the 1995 and earlier trucks; contact us with details of your truck and we can check fitment before you order.

Only registered users are eligible to enter questions