Cart

Quick Links

MegaSquirt 3 MS3 Kit unassembled - ready to build your own MS3 ECU!
MegaSquirt 3 MS3 Kit unassembled - ready to build your own MS3 ECU!
MegaSquirt 3 MS3 Kit unassembled - ready to build your own MS3 ECU!
MegaSquirt 3 MS3 Kit unassembled - ready to build your own MS3 ECU!

MegaSquirt-3 with PCB V3.0 Kit

4.8888888888889 out of 5 based on 18 customer ratings
(18 customer reviews)

$449.99

-

Add the optional Q16 high current coil driver

Bosch BIP373 Coil Driver Mod Kit

Out of stock

SKU: MS330-K Category: Tags: , , , , , , , , , , , , , Brand:

Description

Included is a MegaSquirt-III Engine Management System w/PCB3.0 – Unassembled Kit Part # MS330-K

This MS330-K kit includes everything you will need to build your MegaSquirt-3. The genuine B&G partial kit with V3.0 PCB, everything in the standard Bill Of Materials, the MS3 daughter board kit, the case, pre-machined endplates and heatsink bar, even the tube of heatsink compound and a bit of jumper wire is included. All you add is tools, solder, and time! The MS3X Xpander board is sold separately and allows you to fully take advantage of the MegaSquirt-3, including 8-cylinder sequential injection, 8 ignition outputs allowing 8-cylinder coil on plug, nitrous control, and more. Add a tuning cable to your order if you don’t have one already. 

The BIP373 coil driver is sold separately and is only required for direct coil control. If you are using “smart” coils with internal or ignition modules or “dumb” coils with external ignition modules, you do not need any BIP373 drivers.  You only need BIP373 if you have a dumb coil and do not have an ignition module.  

MS330-K Kit Bill Of Materials (BOM) Includes:

  • MS3 Daughter Card
  • All ‘Basic Components’, including 2.5 bar MAP sensor
  • PWM Flyback Damping Circuit components
  • Hall Sensor/Coil(-) and VR Sensor Ignition Trigger Components
  • Current Limiting Circuit Components

The MS3 daughter card on its own will give you all these features and more:

  • VE and ignition tables are now both 16 x 16
  • 0.1% steps on VE table, 0.1 degree steps on ignition table
  • Socket for an onboard SD card – no laptop required for data logging  (SD Card not included)
  • Built in USB port
  • GM stepper IAC control
  • Closed loop idle and mixture control
  • CANBus communications for interface with GPIO Board, IO Extender, or other devices
  • Staged injection
  • Native support for many different OEM trigger patterns

The MS3 also gives you a starting point for even more expansion. You will be able to connect the headers on this board to additional hardware, such as the MS3X board to enable features like these:

  • 8 channels sequential fuel control
  • 8 channel sequential ignition control
  • Individual fuel and spark trim for cylinder by cylinder tuning
  • 2 and 3 channel PWM IAC control
  • 2 stage nitrous controller
  • Table switching for multi-fuel engines
  • 2 step launch control
  • And more!

For complete MS3 documentation, see ms3efi.com.

 

Customer reviews

Rated 4.8888888888889 out of 5 stars
18 reviews
3 stars 0 0 %
2 stars 0 0 %
1 star 0 0 %

18 reviews for MegaSquirt-3 with PCB V3.0 Kit

Only logged in customers who have purchased this product may write a review.

What inputs and outputs are provided with this kit?

  • It includes the circuitry needed to connect to the following sensors and outputs:
    • Coolant temperature
    • Intake air temperature
    • 2.5 bar MAP sensor (onboard)
    • Oxygen sensor – narrow band or wideband with external controller
    • Throttle position sensor
    • On/off fast idle valve
    • Stepper fast idle valve
    • 2 injector output channels
    • Tach input – Hall effect, optical, or VR sensors supported
    • Single direct coil control spark output
    • Onboard data logging
  • Adding an MS3X expansion card will add sequential injection, eight logic level spark outputs, and more.

I’ve seen a mention of an MS3 Daughter Card. Do I need to order that separately?

  • No. The MS3 daughter card is included as part of this kit.

Does this kit include a MAP sensor?

  • Yes, there is a 2.5 bar MAP sensor included. It is a small UFO-like item in a static resistant bag and will not look like a conventional GM MAP sensor.

What firmware does it have?

  • The daughter card ships without firmware. You will load firmware during assembly.

Questions & Answers

    Does this kit include everything needed to assemble the ms3? including internal wires, case etc?
  1. 0 votes
    Q Does this kit include everything needed to assemble the ms3? including internal wires, case etc?
    Asked by johannes
    A

    This includes the case and everything for the main board including jumper wires. Other add on boards that you can use with the MS3, such as the MS3X expansion board, knock module, and real time clock module, are sold separately.

  2. how well do these ecus handle extreme temperatures and off road vibrations?
  3. 0 votes
    Q how well do these ecus handle extreme temperatures and off road vibrations?
    Asked by robert
    A

    Most components have a -40 to +85 degrees C rating at a minimum - the main exceptions are SD cards and, if you're using a real time clock module, the battery for the clock module. But the SD card and real time clock are not "mission critical", if you're entering a Siberian rally.

    You'll need to Locktite all internal fasteners to avoid vibration, and clamp the wiring harnesses to the body about 15 cm from the backshell exit.

    If this is something like a trophy truck or similarly extreme use, consider an MS3Pro EVO.

  4. Where is R57
  5. 0 votes
    Q Where is R57
    Asked by Rowana Stainrod
    A

    Somewhere in the trashcan of MegaSquirt history. An early bill of materials for the V3.0 board used a different part for Q16 which required a pull-down resistor on its input pin. The VB921 that was originally used for Q16 in early production V3.0s, and the later BIP373, do not require this. Consequently, no standard build guide or bill of materials for the V3.0 board has ever called for anything in the R57 slot.

  6. Jaguar V12, with this type of engine there would be 60 degrees off set for the ignition timing.This because A and B are at 60 degrees apart from each other.How does Megasquirt 3 solve this problem?
  7. 0 votes
    Q Jaguar V12, with this type of engine there would be 60 degrees off set for the ignition timing.Th...... Read more
    Asked by Nigel Barton
    A

    MS3 solves this problem by using six individual spark outputs and skipping the two EDIS modules.

  8. can i run the bmw e46 m52tub25 engine with it? i have a vanos delete kit so i dont have vanos
  9. 0 votes
    Q can i run the bmw e46 m52tub25 engine with it? i have a vanos delete kit so i dont have vanos
    Asked by patrick
    A

    Yes, the MS3 can run this engine - including VANOS with the right mods. You will need to convert to a cable operated throttle body, and if using the BMW coils, you'll need a pair of QuadSpark ignition modules.

  10. Does the kit include Tuner Studio MS Registered Edition or Tuner Studio Lite?
  11. 0 votes
    Q Does the kit include Tuner Studio MS Registered Edition or Tuner Studio Lite?
    Asked by Anonymous user
    A

    TunerStudio Lite is a free download, available at this link. You can purchase the registered version from the TunerStudio site at the "Register Online Now" page. Currently, only ECUs in the MS3Pro family (MS3Pro EVO, MS3Pro Ultimate, and MS3Pro PNP) include the registered version; for all other ECUs, this is sold separately.

  12. Can this use the Microsquirt to control a 4L80E or other GM electronic transmission?
  13. 0 votes
    Q Can this use the Microsquirt to control a 4L80E or other GM electronic transmission?
    Asked by J.R.
    A

    Yes. It would communicate with the MicroSquirt over the CAN bus. You just need to run two wires during assembly to bring the CAN connection to the DB37 connector.

  14. Does this Version have a Knock sensor? I searching for a Upgrade on my AE86 and wanna run 4coilpacks and throttlebodies(tps sensor is needed) a Knocksensor and a Crank Position sensor. And is it possebil to run a transmisson Speed sensor on it. So i can Upgrade my Gauges
  15. 0 votes
    Q Does this Version have a Knock sensor? I searching for a Upgrade on my AE86 and wanna run 4coilpa...... Read more
    Asked by Marvin S.
    A

    You will need to add the MS3 knock module kit to best make use of a knock sensor, and I would also recommend the MS3X expansion board. The MS3 also supports vehicle speed sensor input.

  16. Does this kit come with the RS232 and DB37 connectors etc. to solder on to the board that allows for connection with the wiring harness and a laptop? I understand that the harness's themselves must be purchased separately. Thanks
  17. 0 votes
    Q Does this kit come with the RS232 and DB37 connectors etc. to solder on to the board that allows ...... Read more
    Asked by Sandford Andrews
    A

    We include a solder cup DB37. The RS232 and USB cables are sold separately - as an off the shelf cable is fine for the communication side of things, we don't sell solder cup DB9 or USB connectors.

Only registered users are eligible to enter questions