Cart

Quick Links

MegaSquirt Ford Bias Resistors Mod Kit

MegaSquirt Ford Bias Resistors Mod Kit

$3.99

-

Add to wishlist
SKU: mk-FordBIAS Category: Brand:

Description

This is a simple two-part kit with two 1/4w 27kohm metal film resistors to replace R4 and R7 in any MegaSquirt PCB2.2 or PCB3.0 ECU. This will allow for use of the stock Ford temperature sensors without recalibrating the MegaSquirt for the Ford sensors. Note this is not required, you can recalibrate the MS to work with your stock sensors, this is just another way to go about it if you’d prefer not to mess with the calibration.

NOTE: This kit is for PCBv3.0 and PCB2.2 MegaSquirt ECUs. It is possible to install it on a V3.57, although a bit awkward as you would be putting through hole resistor on a surface mount board.

Customer reviews

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may write a review.

What advantage does this kit have over recalibrating the processor by software?

  • Recalibrating an MS1 is rather involved and can cause problems if you do not configure TunerStudio to match. On an MS2 or MS3, there is less of an advantage to using these. However, they can give a somewhat improved resolution in the typical operating temperature range.

Questions & Answers

There are no questions yet, be the first to ask something for this product.

Only registered users are eligible to enter questions

Related products

  • MegaSquirt Relay Control Mod Kit (VTEC, TVIS, Fans)

     $9.99

    Modkit used to build a relay control circuit, suitable for switching a relay on/off and controlling fans, VVT, VTEC, TVIS, anything a relay can control. Usable on the PCBv3.0, v3.57 or PCBv2.2 ECUs Information and an example of how to implement this...

    Add to cart

  • USB Tuning Cable

     $7.50

    USB A to Mini B cable. Use this with the following products: MS3Pro EVO MS3Pro Ultimate CAN-EGT MS1 or MS2 V2.2 or V3.0 modified with DLP-TXRX mod kit We include this cable with MS3Pro EVO & Ultimate. Does not fit MS3 V3.0 or V3.57.

    Add to cart

  • MegaSquirt Pull-up Resistors Mod Kit

     $3.99

    Six 1k 1/4w resistors, and four 470ohm 1/4w resistors. Perfect for use as 'pullup resistors' for your MS ECU modding needs. These can be used for several of the mods described in some of our car-specific install articles listed on the site. NOTE: Th...

    Add to cart

  • MegaSquirt PWM IAC Valve Control (TIP120) ‘Mod-Kit’

     $9.99

    These are the parts needed for the 'TIP120 PWM idle valve' mod.  If you are installing all optional components on the v3 heat sink (leaving no extra space for this transistor there) then you can drill a hole in your case and use it as your heat sink or a...

    Add to cart

  • DLP-TXRX Internal USB/Serial Adapter

    5 out of 5
    $31.00

    DLP-TXRX Internal USB/Serial Adapter This adapter is perfect for converting your Megasquirt from the standard DB-9 serial connection to the USB connection common on newer laptops. The DLP-TXRX can be used on the following MegaSquirt products: MS1 ...

    Add to cart

  • MegaSquirt Boost Control Mod Kit

    5 out of 5
    $9.99

    Give your Megasquirt the ability to drive a boost control solenoid double up it's duty as an electronic boost controller. Includes all parts required to build the MSnS-E boost control circuit on your V2.2, V3.0, or V3.57 PCB, including FET, resistors, hea...

    Add to cart