Cart

Quick Links

JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled
JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled
JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled
JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled
JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled

JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled

5 out of 5 based on 4 customer ratings
(4 customer reviews)

$119.99

-

Frequently purchased together

Jumper 10-Pack

MegaSquirt JimStim Stimulator Power Supply

Description

DIYAutoTune Part# JimStim-C

JimStim is essentially an engine simulator, a microcontroller which allows the generates up to 30 different toothed wheel signals, in addition to the standard distributor signal. Test your RPM input on the Stim, or tell the JimStim to provide a signal like the one from a Neon, Miata, Subaru, most Fords, and many more. It can also drive ignition input mods with pull-ups.

JimStim includes a set of user-configurable jumpers that for testing IAC motor outputs, spare inputs, and spare outputs. You can wire these up with the selection jumper wires. There is also a bank of screw terminals that let you connect things other than a standard Megasquirt to the JimStim.

The current firmware allows you to connect the JimStim to a laptop using a special cable, FTDI part number TTL-232R-3V3. This is not needed for regular operation, but lets you set the wheel pattern and output speed to display via TunerStudio, and allows you to program in custome wheel patterns or make the JimStim sweep its RPM output. As most users will never need this cable, we currently do not stock it, but could add it if there’s enough customer interest. Right now it can be ordered from Digi-Key under part number 768-1015-ND.

To power your JimStim, we recommend our 12 volt Stimulator power supply.

You can find the JimStim documentation and assembly instructions at this link.

This one is fully assembled and ready to go. It includes three jumper wires like the ones shown in the picture. If you need more for additional features, order our 10-pack of extra jumpers.

Power supply requirements: 9V battery or StimPower

Customer reviews

Rated 5 out of 5 stars
4 reviews
4 stars 0 0 %
3 stars 0 0 %
2 stars 0 0 %
1 star 0 0 %

4 reviews for JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled

Only logged in customers who have purchased this product may write a review.

What applications call for a JimStim, and when can I use a regular Stim instead?

  • The regular Stim can be used for installs when you are using just fuel control, a simple distributor, or a Ford EDIS ignition. The JimStim can do all that plus simulate missing toothed crank triggers, distributorless ignitions, and test considerably more inputs and outputs. We recommend using the JimStim if you anticipate that you might need any of these capabilities.

Can I connect a JimStim to MegaSquirt systems that do not have a DB37 connector, like a DIYPNP or MicroSquirt?

  • This is a bit more involved than testing a regular MegaSquirt, but you can make an adapter harness that either connects to the DB37 or the screw terminals, using the appropriate plug for your ECU on the other end.

Can the JimStim be used for non-MegaSquirt ECUs?

  • Yes, we have had customers use it for other aftermarket and OEM controllers using adapter harnesses. We cannot promise that its outputs will be exactly what your system requires. Contact us if you need support for a non-standard application.

What is the JimStimX?

  • The JimStimX is an add on to the regular JimStim to allow testing MS3X outputs. See the JimStimX documentation for details.

Where is this unit assembled?

  • We assemble them in-house here in Gainesville, Georgia, USA.

What sort of warranty does this have?

  • It has a one year limited warranty against manufacturing defects.

I’ve seen mention of an FTDI cable. Do I need one of these?

  • The FTDI cable is only used for very advanced features like uploading custom wheel patterns. Very few users will need this.

Questions & Answers

    I am hoping to simulate an older BMW engine which uses a 60-2 crank wheel and a cam indexing pulse. Which crank tooth is the cam pulse synced to, and can it be adjusted? In my application, the real engine makes the cam pulse 144° BTDC during cylinder 1's compression stroke. Thanks.
  1. 0 votes
    Q I am hoping to simulate an older BMW engine which uses a 60-2 crank wheel and a cam indexing puls...... Read more
    Asked by William
    A

    The standard 60-2 pattern in the JimStim has the cam signal trigger between teeth 36 and 37, and lasts for 3 simulated crank degrees. Altering the pattern is a bit complicated but possible, using a text file and a program from the JimStim website.  You will need an FTDI TTL-232R-3V3 cable, not included, to upload alternative wheel patterns.

  2. will this work with the SR20DET wheel and what settings
  3. 0 votes
    Q will this work with the SR20DET wheel and what settings
    Asked by clive Morgan-Davies
    A

    The JimStim currently does not have a mode to emulate the factory SR20DET cam angle sensor, but it can emulate our replacement trigger disc. Our trigger disc is equivalent to 12-1 mode - DIP switches 4 and 6 on, all others off.

Only registered users are eligible to enter questions