Showing 17–32 of 451 results
-
MS3Pro ULTIMATE Universal Harness
$299.00MS3Pro ULTIMATE Complete 8' Flying Lead Harness Only (White-Black-Gray connectors with 8' pigtails) arrives with color-coded, printed wires per the pinout below. All applications.
Add to cart -
MicroSquirt Wiring Harness – 8ft
$89.00Included is an 8' long harness for installing the MicroSquirt on larger vehicles instead of motorcycles and ATVs. Serial cable included.
Add to cart -
MS3Pro ULTIMATE Center Harness
$49.00MS3Pro ULTIMATE adds nearly 50% more I/O with the addition of a third AMPSEAL 23-pin, 8' flying lead. Harness arrives with color-coded, printed wires per the pinout below (black center connector) ***Center Harness ONLY in this listing ...
Add to cart -
MS3Pro EVO Uncrimped AMPSEAL Connectors
$60.00Making your own harness? This plug and pin kit features the MS3Pro AMPSEAL white & gray connectors plus 75 pins- more than enough for making your own MS3Pro EVO or 1st Gen harness. MS3Pro ULTIMATE 3-connector AMPSEAL Kit available here
Add to cart -
MS3Pro ULTIMATE Uncrimped AMPSEAL Connectors
$82.00Planning to make your own ULTIMATE harness? This plug and pin kit features the MS3Pro ULTIMATE AMPSEAL white, black & gray connectors, plus 100 pins- more than enough for making your own! (EVO/ 1st Gen 2-connector AMPSEAL Kit sold separately)
Add to cart -
MicroSquirt AMPSEAL Connector
$35.00Planning to make your own MicroSquirt harness? This plug and pin kit features a 35 pin MicroSquirt connector and more than enough gold plated pins!
Add to cart -
MS3Pro 1st Gen Wiring Harness Upgrade (for ULTIMATE and EVO)
$22.00If you have a previously installed MS3Pro harness (1st Gen flying lead or LS Drop On Harness) and want to upgrade to MS3Pro EVO or ULTIMATE ECU, the upgrade path is simple. However, complete functionality will require a few basic changes to your 1st Ge...
Add to cart -
USB to Serial Adapter -TunerStudio
$22.49This USB to Serial Adapter has been tested and works properly with all versions of TunerStudio. We highly recommend this adapter is used if your tuning PC/laptop doesn't have a DB9 Serial connector. Or you can use another adapter with a genuine FTDI c...
Add to cart -
4 Pin M12 Serial Cable
$31.50Connect MS3Pro ULTIMATE or EVO directly to your laptop with this 4 pin M12 serial cable.
Add to cart -
4 Pin M8 Serial Cable
$31.50Replacement M8 to DB9 serial cable. This cable is used for certain plug and play applications where there wasn't room for a regular DB9 connector, including the following: MS3Pro PNP for '84-'87 Buick Regal 3.8 Turbo MSPNP Gen 2 for '86-'93 Ford M...
Add to cart -
Sealed resistor – 10K
$4.50We've wrapped a 10K, 1/4 watt resistor in a sealed and strain-relieved package for underhood use. Red heat shrink tubing with yellow leads. Typically used as a shunt resistor with VR sensors.
Add to cart -
Sealed resistor – 1K
$4.50We've wrapped a 1K, 1/4 watt resistor in a sealed and strain-relieved package for underhood use. Blue heat shrink tubing with blue leads. Suggested uses include a pull-up resistor for Hall effect and optical sensors, and for spark outputs C and D on a Mic...
Add to cart -
Seals-It Grommet – 0.75″ one piece
$18.00Seals-It grommets make it easy to run wiring through your firewall without risking wearing the wiring, and help keep dirt and grime out of your interior. This one is a one piece, 0.75" inner diameter design that's perfect for any of our flying lead wiring...
Add to cart -
Seals-It Grommet – 1.00″ split
$29.00Seals-It grommets make it easy to run wiring through your firewall without risking wearing the wiring, and help keep dirt and grime out of your interior. This one is a split 1.00" inner diameter design that can slip over our finished drop-on wiring harnes...
Add to cart -
MS330-K Kit with MapDaddy4
$509.00MegaSquirt-III Engine Management System w/PCB3.0 - Unassembled Kit Part # MS330-K_m4 Important Note: The BIP373 coil driver is sold separately and is only required for direct coil control. If you are using coils with internal or external ignition modul...
Add to cart -
MegaSquirt-III with PCB V3.0 Kit
$445.00Included is a MegaSquirt-III Engine Management System w/PCB3.0 - Unassembled Kit Part # MS330-K Important Note: The BIP373 coil driver is sold separately and is only required for direct coil control. If you are using coils with internal or externa...
Add to cart